5 Seats Full Set Car Seat Covers PU Leather For Interior Accessories

Glove design created by FIVE, often copied but never equalled, the STUNT is considered, and rightly so, as the original of its kind. It is evolving to become the STUNT EVO and features a new design and brand new knuckle-protection shells, along with new carbon-fibre palm protection. Characterized by its leather palm, the secure snug fit, comfort, and control are outstanding thanks to its fabric topside structure. Pull-tab for easy-on/off. Perfectly suited for regular city driving. In the REPLICA version, the graphic is a fundamental element of the model. Shape adapted to the form of a woman’s hand.

Mainline editions come with matching colored cheek pads and liner Helmet Technology
Shell Design: An aerodynamic shell design constructed using an advanced lightweight composite poly-alloy. This helmet is specifically designed to fit adolescents and small adults Ventilation: 11 points of ventilation with chin, side, forehead, top and rear vent. 3 intake vents and 8 exhaust vents Google Guide on Eyeport Trim: Goggle strap grabbers Visor: A removable and adjustable (50mm) screw-on visor This helmet model meets or exceeds both ECE 22.05 and DOT FMVSS-218 motorcycle helmet safety standards Retention system is a race approved Double D-RING A clear coat finish to protect paint & graphics A large-size FX-17 weighs 1.55 kg or 3.42 lbs
Removable, washable and custom sizable Interior AFX helmet liners and cheek pads are made with a hypoallergenic andanti-microbial nylon, most of which are removable and washable. The size of this helmet is based on a combination of four factors: outer shell size, inner EPS thickness, comfort liner thickness and cheek pad thickness. The fit of the helmet can be customized by replacing your existing cheek pads with thinner cheek pads (for a looser fit) or thicker cheek pads (for a tighter fit). The fit can also be customized by replacing your existing comfort liner with a thinner comfort liner (for a looser fit) or thicker comfort liner (for a tighter fit). Please refer to the shell, liner and cheek pad compatibility chart below. Keep in mind these components can only be replaced inside the group of sizes contained in each size range block.

Helmet Shell & EPS Size XS-M L-XXL



XS S M L XL XXL

Check Pad Thickness (mm) 28 24 20 28 24 20

Comfort Liner Thickness (mm) 10 8 6 10 8 6

€Lady Glove in short sizes made of leather and textile mix
Features
soltoTEX® membrane with Tri-fleece inner lining Palm made of Clarino with double layer of leather Stretch leather on back of hand Fingers with double layer of leather Wrist stretch adjustable with Velcro Width adjustable cuffs with Velcro fastener Safety: fulfill the requirements of the directive N° 89/686/EEC

Ergonomics
Ergonomic fit
Temperature adjustment
Windstopper® fabric Keeps the body dry and warm

Aluminium German Germany Flag Badge Grille Emblem Decal Universal DecorationFeature:1. 100% brand new and good quality German Flag Emblem.2. Made with high quality of Aluminum material.3. Adhesive on back, suitable to fix it in front grille steadily.4. Universal fits for most car, such as Volkswagen, Audi, etc..Specification:MaterialAluminium DimensionApprox 63mm*32mmColorYellow+Red+Black PatternGerman FlagInstall PositionFront GrilleQuantity1 pcsWeight9gNote:Please clean the target place by detergent before stick it on.Package Included:1 x German Flag Badge Sticker

MR. JUMP, the fiber helmet studied in details for comfort, technology and for sure safety for end user. It has been studied and tested to optimize the outside and inside air flows.
OUTER SHELL in tricarboco material, mix of Kevlar, carbon and fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell sizes: XS-L and XL-2XL
INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M and L). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation.
The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding.
MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471
CHEEK PADS completely removable and washable, with different thickness to get a perfect customization od the helmet.
INTERNAL SHELL completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet and to let off the hot air through the back part.
INNER (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper and back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation.
The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses.
weigth: ca. 1000gr