Leatt GPX 1.5 GRipR Art, gloves

MR. JUMP, the fiber helmet studied in details for comfort, technology and for sure safety for end user. It has been studied and tested to optimize the outside and inside air flows.
OUTER SHELL in tricarboco material, mix of Kevlar, carbon and fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell sizes: XS-L and XL-2XL
INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M and L). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation.
The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding.
MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471
CHEEK PADS completely removable and washable, with different thickness to get a perfect customization od the helmet.
INTERNAL SHELL completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet and to let off the hot air through the back part.
INNER (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper and back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation.
The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses.
weigth: ca. 1000gr

Description:Euro LightsFastEasy InstalledLamp with long life expectancyWaterproofWeatherproof and 100% Rust FreeSpecification:Product Name:Turn Signal LightMaterial: PlasticColor: Yellow,clear,tanSize:120x45x53mm(LxWxH)Surface Finish: PlasticManufacturer Part Number: 002001-0197Placement on Vehicle:Front ,Rear,Left, RightFitment:For BMW F 650GS 2008-2012For BMW F 800GS 2008-2012For BMW F 800R 2008-2014For BMW F 800S 2006-2010For BMW F 800 ST 2007-2011For BMW HP2 Enduro 2005-2010For BMW HP2 Megamoto 2006-2010For BMW HP2 Sport 2008-2010ForBMW K 1200R 2005-2008ForBMW K 1200S 2005-2008ForBMW R 1200GS 2004-2013For BMW K 1300R 2009-2014Note:1. We provide clear pictures, measurements where possible.Please check as much as possible to make sure the item is the one that you need.2. Please allow 0.5-1 inch difference due to manual measurement.(1inch=2.54cm)3. Instruction is not included,professional installation is highly recommended.4. The color of the actual items may slightly different from the listing imagesdue to different computer screen, thanks for your understanding.Package Included:1 X Pair Turn Signal Light

Receive your calls easily with your Twiins D1 hands-free. Very easy to install, it fits in most helmet models, and it is fully inte­grated inside the helmet.
Specifications: Connect your phone and receive calls using only one button. Ready to connect with cellular phones and smartphones Blue­tooth®. Compact and miniaturized electronics integrated on one speaker. LED red/blue indicator showing the state of functioning integrated on the microphone. Intercom available by linking with a Twiins D3 or D2-HSAi Answer your calls or follow GPS instructions. Rechargeable by USB. Easy to install.

The Essential ist ein Handschuh, der das Beste aus beiden Welten bietet: Ideal für den täglichen Gebrauch und lange Reisen.Handfläche: 100% Ziegenleder Externe Schutzoberteil für Mittelhandknochen. Multiple Verstärkungen mit doppelter Schicht und zusätzliche Schaum auf Bereiche gemacht, um Abrieb in einer Crash-Situation ausgesetzt (Palm, Seite der Hand, Finger) Ringfinger und kleinen Finger werden zusammen mit einem Lederstück gehalten. Halb Textil-, Halbziegenleder und vorgeformte der Must bietet ein hohes Maß an Komfort. Comfort Verstärkung an der Spitze der Handfläche und Daumen in den Einsteller auf dem Handgelenk und onthe Manschette. Zwischen jedem Finger, an der Unterseite, ist platzieren eine bestimmte Textileinlage, um überlegene Stufe des Komfort Minibar und ein S. Finger Steppnähte an der Außenseite positioniert, für besseren Komfort.