Free
Support
ABUS 55 Series solid brass body padlock with the inner components made from non-corrosive materials. Pin tumbler cylinder with anti-pick mushroom pins which resists picking, a hardened steel shackle which resists hacksaw attacks and is double bolted 30mm and above for increased shackle strength. Long shackle (HB) version available : For most security needsOverall width: 38 mmOverall height: 60 mmOverall depth: 13 mm Shackle width: 20.5 mm I.D.Shackle height: 21.5 mmShackle Dia: 6.5 mm
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S
Thor super plastic hammers have a malleable iron head fitted with cylindrical ultra-high molecular weight polythene faces which are designed to wear and be replaced. Available in 3 different weights. The ultra-high molecular weight polythene heads provide high impact, durability and high abrasive resistance. The faces will not fracture, splinter or delaminate. Ideal for use as a general-purpose, soft-faced hammer in engineering applications for assembly, repair and maintenance operations as an alternative to a rawhide faced hammer. Size: 2.Weight 790g (1 3/4lb).Diameter 38mm (1 1/2 in).
The Einhell Power-X-Change Starter Kit, contains the following: 1 x Power-X-Change 18 Volt Charger that features a 6-step charging condition display and is ready for wall-fastening. The charger uses an intelligent charging-management-system for long battery life (battery status will be constantly checked and accordant loaded, deeply discharged battery will be charged in repair mode). Input Power: 240 Volt.Output Voltage: 21 Volt.Charging Time: 1.5Ah: 30 Min, 3.0Ah: 60 Min, 5.2Ah: 130 Min. Weight: 0.5kg. 1 x Power-X-Change 18 Volt 2.0Ah Li-Ion Battery that features a 7-in-1 ABS: Active Battery Management System and a 3-Step LED battery control. The microprocessor controls key parameters like temperature, voltage and even a deeply discharged battery can be charged in repair mode which offers a long working battery life. The high quality Li-Ion battery cells provide nearly no self discharge and the rubber coated housing gives high impact protection and a high grip. It also has a recessed grip that ensures good ergonomic handling. Battery Type: Li-Ion.Voltage Supply: 18 Volt.Battery Capacity: 2,000 mAh.Product Weight: 0.4kg.
Metric combination spanners offset at 15° - DIN 3113A. Manufactured from chrome vanadium steel with a satin finish.Size 17mm.Length 210mm.
The Stabila 80T Telescopic Level allows you to always have the right length of level, no matter what job you need to do. The levels are adjustable meaning there’s no need to carry around several levels any more. Simply adjust the level length by sliding out the high quality extension bar, and lock into place to fix the length. A printed metric scale allows you to easily work out inner dimensions and clearances. The top edge of the level is continuous, even when extended making it easier to mark out your measurements. Integrated anti-slip stoppers on the back edge of the level allow for a firm hold when marking against flat surfaces, the spirit level will not slip giving you a free hand to mark out or cut against the level. Stabila’s unique vial installation technology ensures the components of the spirit level are firmly bonded forever. You can trust that your spirit level will retain its accuracy for life. With 2 vials: 1 plumb and 1 horizontal, with a measurement accuracy of 0.029° = 0.5 mm/m (closed) and 0.057° = ± 1.0 mm/m (extended).The Stabila 80T Telescopic Level has the following specifications: Length: 63-105cm.
