The Britool 3/8in Drive 22 piece metric bi-hex socket set is supplied in a socket set case which also converts into a modular storage system for use in roller cabinets. Consisting of: 17 x 3/8in Bi-Hex Sockets: 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 21, 22 & 24mm.2 x 3/8in Extensions: 75 & 125mm .1 x 3/8in Bit Holder 1/4in.1 x 3/8in Universal Joint.1 x 3/8in Reversible Ratchet.
The Plantpak by Crest Windowsill Heated Propagator is a premium quality electric 3 bay propagator, which is durable and robust. It comprises 3 pots and a water reservoir. The pots each have shatterproof covers and adjustable ventilation for air flow and humidity. The 1.4 Litre water reservoir removes the need for daily watering. The propagator is ideal for the beginner and experienced gardener. It is designed to provide an even heat distribution of 16-19°C. Supplied with 6 varieties of Unwins Seeds. Voltage: 230 Volt.Cable Length: 2m (Cable Included).Dimensions: 54.5 x 22 x 16.5cm.
Teng Tools impact sockets are specifically designed for use with power tools and air tools. Manufactured in chrome molybdenum in accordance with GGG-W-6608, these sockets ensure the highest quality. They are size marked for easy identification. These regular 6-point deep impact sockets have a 1/2 inch square drive. They are manufactured to the latest DIN standard for industrial use.The TEN920624 Impact Socket has the following specifications:Size: 24mm. Length: 78mm.
The Lindstrom Supreme Oblique Cutting Nipper produced from high performance tool steel. It has a screw joint that minimises friction and alignment of cutting edges. The edges are precision induction hardened to 58-60 HRC. The handles with return spring and sleeved.Length (A): 108mm (4.25 in).Blade length (B): 8mm (0.31 in). Head width (C): 10.5mm (0.41 in). Head depth (G): 15mm (0.59 in). Cutting capacity: 0.35-1.25mm. Head type: Double angled. Cutting edge: Flush. Angled heads, also known as oblique style, are set at an angle to the main body of the cutter. This means that the cutter can reach between parts and areas which are difficult to access. The Flush Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are ‘pinched’, allowing less altitude and a smaller overall surface area – more than Micro-bevel cuts. The cutters have fine cutting edges that leave a narrow and short taper and small exposed area. They can be used to meet tight specifications for a flush result to a board, component or part.
Forgefix Hex Flange Head Lightning Bolts provide a virtually stress-free fixing for close to edge applications. They are self-threading and allow quick and easy installation of most masonry fixing applications. They can simply be screwed into a pre-drilled hole, without the need for a sleeve or plug. The bolts are through-fixing, eliminating the need for marking and re-positioning. They have a high load capacity due to the thread interlocking into the base material. The flange head acts as a fixed washer, distributing the load under the bolt head. The bolts have an 'Elementech' coating for superior anti-corrosion, which has been salt spray tested to 1,000 hours. Applications: Suitable for most masonry substrates including concrete and brickwork but also for hollow block or bricks due to the nature of the thread type anchoring along the total length of the fixing.Specifications: Size: M6 x 75mm.Pack quantity: 100.
Hammerite "Direct to Rust" Metal Paint can be painted directly onto rusty surfaces and, thanks to its special 3-in-1 formula, there is no need to use a primer or undercoat...saving you precious time! It forms a superior barrier that not only seals out moisture, but also gives long-lasting protection, both inside and outside. Touch dry in an hour, Hammerite is corrosion-resistant and is suitable for use on a wide range of exterior metal including gates, railings, drainpipes, guttering and garden furniture. Two coats are required and protects up to 5 years. Specification: Colour : Red Finish : Smooth Size : 400ml Coverage : 0.5m²/L
