Free
Support
Palo telescópico plegable ultraligero portátil retráctil varilla plegable herramienta de protección de autodefensa al aire libre
The Forgefix Nyloc Hexagonal Nuts incorporates a nylon component to effectively lock the nut into position on the bolt. The nylon component has a smaller inside diameter than the actual nut. This locks the nut in place by squeezing the nylon firmly around the bolt when tightened. Unlike a standard locking washer, the Nyloc nut prevents the nut from loosening under vibration as the nylon is tightly wedged into the bolt threads and provides resistance to turning when tightened. The nuts are zinc-plated for increased resistance to corrosion. Their hexagonal shape is designed to be driven by a wrench (spanner) and provides excellent torque when done so. APPLICATION: Where a permanent fastening is required and loosening must be prevented by movement or vibration. Can be used on most bolt products including HT Bolts, Carriage Bolts, Threaded Rod etc. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers.Nyloc Nuts & Washers Zinc Plated M4 Forge Pack 50
Multi-purpose combination square for use in both wood and metalworking applications. Each square features a high quality cast and machined sliding stock, fitted with a stainless steel rule engraved with both imperial and metric graduations, a spirit level and marking scribe.The Faithfull combination square has at least 10 different uses including:-Measuring rule with metric and imperial scale, 90° inside square, 90° outside square, 135° inside square, 45° inside square, horizontal level, vertical level, T-square slide, marking gauge and depth gauge.Ruler Length : 400 mm / 16 inch.
Paslode IM350+ Diamond point clipped head Nail packs with paper strip, supplied with Paslode Special Impulse gas fuel cells.FINISH: All Paslode nails are Chrome 6, cadmium and lead free and are available in five finishes to meet corrosion requirements.Bright: Economy and bright nails meet the Eurocode 5 requirements for applications in service class 1 (indoor) Specification - No coating.Galv Plus : Meet the Eurocode 5 requirements for applications in service class 1 and 2 (indoor and covered outdoor) Specification - Zn / Al alloy approx 15µm.Electro Galv : Meet the Eurocode 5 requirements for all applications in service class 1 and 2 (indoor and covered outdoor) Specification - Zn and chromate minimum 7µm.Hot Dipped Galv : Meet the Eurocode 5 requirements for all applications in service class 1, 2 and 3 (indoor, covered outdoor and outdoor) Specification - Zinc coating minimum 50µm Stainless Steel : Meet the Eurocode 5 requirements for all applications in service class 1, 2 and 3 (indoor, covered outdoor and outdoor) Specification - A2 according to AISI 304, and A4 according to AISI 316.SHANK: Smooth Shank: The standard nail, offering high shear value and lowest withdrawal resistance. Fixing across the grain. Fixing into end grain. Clenching applications. Specification - Number of centres will vary with shank diameter.Unilock Shank : Increases withdrawal resistance. Drives easier than ring shank fixing across the grain. Specification - The ringed parts have 24 rings per inch.Ring Shank : Provides the highest withdrawal resistance. Fixing across the grain. Specification - RPI (Rings Per Inch) vary from 16 to 32 depending on Specification.HEAD TYPES :Round Head : The head area is designed to maximise resistance to the head being pulled through Specification - Head size between 2.0 and 2.5 times wire diameter according to EC5Clipped Head : Increases number of nails per strip. The head area is designed to maximise resistance to the head being pulled through Specification - Head area corresponding to full round head area, according to EC5
The Carver Medium-Duty Rack Clamps have a variety of uses. The most common include welding, metal fabrication, moulding box and die holding, plate fabrication, plastic and fibreglass moulding and maintenance work.The Carver T290-450 Medium-Duty Rack Clamp has the following specification: Capacity: 450mm (18in).Reach: 90mm (3.1/2in). Overall Length: 655mm (25.3/4in).Clamping Force: 1,800N.Weight: 7.0kg.
Type:Standard Spout; Style:Antique; Finish:Nickel Brushed; Faucet Type:Kitchen faucet; Installation Type:Centerset; Valve Type:Ceramic Valve; Faucet Body Material:Brass; Faucet Spout Material:Brass; Bodysprays Included:No; Handle Material:Zinc Alloy; Batteries Included:No; Installation Holes and Handles:Single Handle One Hole; Features:FaucetSet; Shipping Weight:1.2; Net Weight:0.8; Listing Date:02/26/2021