Free
Support
To have a maximum safety the helmet must fit tightly and be correctly and securely fastened, in order not to be able to be taken off neither by pulling it nor by rotating it around the head. If it is too big, it may slide down over the eyes or turn in a lateral direction due to movement during riding, blocking the right visibility. Safety SHELL in TRICARBOCO material, mix of Kevlar, carbon and fiber, joint through resine, hand made, using new technologies with vinilester resin. The INTERNAL POLYSTYRENE produced in 3 sizes to get the best fitting. This characteristic allows a gradual and progressive absorption of the energy produced by the impact. Even if the bigger part of the energy created by the impact is absorbed by the external shell, thanks to its deformation, the role of polystyrene is determinant for the absorption of the residual energy. A diversified density of the polystyrene, permit us to optimize the mechanical performance of the shell/polystyrene. The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding. ECE 22-05 Ventilation The internal polystyrene has been studied to work together wityh the air ventilations, put on the shell. The channels allow the perfect inside air flow and at the same time a quick outside air flow from back ventilation. Comfort The CHEEK PADS and the INTERNAL COMFORT shell can be removed, washed and replaced.
They are made of a precious fabric with specific fibers, that offer:
It moves away the body sweat, Keeps rider fresh, dry and completely comfortable, Lightweight, soft and breathable fabric, Performance controlled and certified by ADVANSA.
The cheek pads are easily removable also in case of accident through a red strap which removes the cheek pad even if the helmet is worn by the rider.
The Leatt 2.5 Talon Chest Protector offers lightweight premium hard-shell roost protection. The 3D design and adjustable waist straps offer a close fit that is also comfortable as well as ventilated. Features
Hard shell protector Our 3D design ensures a great fit that is very comfortable. Padded base layer Close fitting allows for over or under the jersey use. Recess areas in both front and back integrates with Leatt® neck braces perfectly. Adjustable waist straps for great fit
Specifications
Brust protection: EN 14021 Weight: 650g (1.43lbs) Unisex Fit: 60 to 90 kg (132-198lbs)
Thanks to breakthroughs in the study of aerodynamic phenomena, SKWAL boasts a design and silhouette resulting from computational fluid simulations, in the aim of optimizing both stability and soundproofing at high speed. The one-of-a-kind SKWAL lines are reinforced and transformed by 3 embedded LEDs powered by a rechargeable battery (USB charging cable included). SKWAL is one of the world s first major integrated manufacturers to be equipped with this technology. Features
1,470 g Constructed from injected thermoplastic resin Pinlock MaxVision visor a standard feature Visor can be fitted with a Pinlock Max Vision® film insert Quick release visor system "Autoseal" system: flattens the visor onto the helmet, offers better soundproofing and seals the helmet (against water and cold) Integrated UV380 label & anti-scratch sun visor Optimal comfort for the persons wearing glasses Micro lock buckle system Planned location for SHARKTOOTH® Interior bamboo treatment for triple effectiveness: antibacterial, anti-sweating and hypoallergenic
Its High Strength And Quick Set-Time Make Gorilla Super Glue The Go-To For A Variety Of Household Projects, Developed For Long-Lasting Repairs In An Instant, Gorilla Super Glue Dries In 10–30 Seconds And Is Reinforced With Rubber For Increased Impact Resistance, We Call It Impact-Tough Because It Stands Up To Wear And Tear Unlike Any Other Instant Glue, In Addition To Its High-Performance Formula, We‘ve Added An Anti-Clog Cap With A Metal Pin Inside To Ensure An Airtight Seal For Maximum Reusability, It‘s Gorilla Tough, Every Time, Grip Time: 10-30 Seconds, Open Time: Not Repositionable, Dry Time: Light Handling After 1-5 Minutes, Dry Color: Translucent, Full Cure: 24 Hours
Incorporating a host of protection and performance innovations the certified Atem v3 Suit is constructed from premium, supple leather and is ideal for track or street use. With technologies developed and extensively tested in MotoGP, the Atem Suit fuses exclusive ergonomic styling and class-leading protective technology. Features
Extremely durable 1.3 mm leather construction with flexible leather accordion panels on the lumbar area, back, knees and elbows for superb comfort and performance fit and ease of movement on the bike Features Alpinestars Hyper-Res Stretch Fiber (HRSF) stretch inserts on crotch, back and underarms for excellent fit and movement Strategically placed perforation panels on upper and lower body for improved ventilation and internal airflow
Protection
Fully certified garment Certification includes all materials, construction and protectors, which have been independently tested and assessed to meet standard performance requirements Class-leading protective capabilities â internally and externally Removable certified, race-developed GP-R internal protectors offering lightweight performance and superior impact protection to shoulders, elbows, knees, tibia and shins Alpinestarsâ new, exclusively developed shoulder GP Dynamic Fiction Shield (GP DFS) protector, which is anatomically contoured and incorporates a triple density polymer compound for improved performance in crash slides. The GP DFS protection is ergonomically designed for improved upper body flexibility and features over-injected mesh air inlets for excellent airflow Innovative new elbow slider is anatomically contoured and incorporates a triple-density polymer compound for improved performance in crash slides. The elbow slider features a removable and replaceable screw-mounted insert slider for unsurpassed friction management Dynamic Fiction Shield (DFS) knee protection and GP knee sliders offer additional abrasion resistance in a key impact area Chest and back pad compartments with advanced poly-foam padding (certified Nucleon chest and back inserts available as accessory upgrade) Snap connections allow integration of level 2 certified Nucleon Race Back Protector for critical spinal protection Garment comes supplied with anatomically profiled and removable Nucleon hip protection
Performance
Ergonomically engineered âArshieldâ reinforcements, consisting of aramid fiber and polyamide, strategically positioned on sleeve and knee for critical seam reinforcement MotoGP-profiled, aerodynamic back-hump is ventilated and improves suit cooling performance Neoprene-edged collar and cuffs prevents chafing and improves comfort Interior leg and cuffs feature taslon fiber closures to keep suit firmly situated on body Reinforced inner arm and leg cuff adjustments with hook and loop grip closure for durability Removable multi-panel lining and new, redesigned 3D mesh inserts to improve comfort and ventilation Zippered calf expansion gusset improves range of fit and riding comfort Inner waterproof pocket for safe storage of documents
