Stabila 196-2 Electronic Level 60cm 16384

These Thor Nylon Hammers have split cast iron head with two nylon faces fastened securely to the handle with two socket head cap screws. Head design allows quick adjustment or replacement of either the handle or the faces, while the faces are designed to wear, and can be rotated for even wear.For use as a heavy-duty, multi purpose soft-faced hammer in most industries for assembly, repair and maintenance operations.Diameter: 50mm (2 in).Weight: 2100g (4 1/2 lb).

Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S

The Bulldog 1811 Premier Grass Hook is ideal for cutting rough grass and general roadside or field maintenance. The flat blade on this tool is ground on both sides so it can be used left or right handed. Fitted with a handle hook for easy storage. Made In Britain.

DEWALT Mesh Sanding Discs last at least 4 times longer than traditional DEWALT sandpaper discs. Fibres are drawn away from the surface of the sanding disc into the small holes, and don't sit between the material and abrasive. This optimises the sanding effect. These sanding discs enable dust to be drawn through the mesh across a wider area rather than being limited to distinct holes in traditional sanding discs. They are also much easier to select as there is no requirement to match a specific dust extraction hole pattern. The mesh sanding discs have hook and loop fastening for quick and easy attachment. They can be easily cleaned to help prolong their life.The DTM3133 Mesh Sanding Discs have the following specifications:Size: 150mm.Grit: 80.Pack quantity: 10.

The Milwaukee M18 BRAID-0 Right Angle Impact Driver has a compact design and measures 307mm in length and a 53mm head design, making it ideal for working within confined spaces. The full metal gearbox and gears provide superior durability and maximum torque in even the toughest applications. There is a multi-handle design with an extended paddle switch for multiple grip positions and maximum comfort. The 1/4in Hex chuck provides quick and easy one handed bit change and there are 2 speed settings, that allow for a wider range of applications. REDLINK™ overload protection electronics in tool and battery pack deliver best in class system durability. Individual battery cell monitoring optimises tool run time and ensures long term pack durability. There is also a on board fuel gauge and LED light. Bare Unit, No Charger or Battery Supplied. Specification No Load Speed: 0-1,500/0-2,250/min.Impact Rate: 0-2,400/0-3,400/bpm.Max Torque: 41/81Nm. Weight: 1.8kg.

An all round tool that delivers around 57% more run time than brushed motors due to its brushless motor, the compact 300w motor provides 0-22,000 oscillations per minute, providing quicker completion of the most challenging tasks. Featuring the latest DeWalt quick-change accessory system, the user can swap blades and attachments fast and safely without using any other tools. The dual grip variable speed trigger ensures safe application control and ultimate speed, as well as a dual position rocker switch and a front mounted LED work light.Great for cutting in drywall or skirting, cutting fabrics, clean grout removal, pipes or timber, flooring, sanding, scraping or preparing surfaces, this Oscillating Multi-Tool ensures comfortable use over extended periods thanks to its rubber over mould and ergonomically designed handle.A 29 piece accessory kit is also included, featuring accessories for sanding and cutting jobs:1 x Fastcut wood blade 1 x Wood with nails blade1 x Sanding pad1 x Universal adaptor25 x Sanding sheets