The Knipex 26 21 200 bent long nose side cutters have long flat round jaws that are highly loadable, with elastic precision points with blades for hard wire diameter up to 2.2mm and medium wire diameter up to 3.2 mm. The cutting edges are separately induction hardened for durabilty and longer working life and are hardend to approximately 61HRC. The jaws are angled at 40° and are ideal for use on electronic or tight to reach areas on computers, circuitry, or motor vehicles applications. Knipex have used a good quality special tool steel material that is oil hardened. Dipped handles.The Knipex 26 22 200 bent long nose side cutters have Bi-material, 2-component handles for a more comfortable and positive grip. They have long flat round jaws that are highly loadable, with elastic precision points with blades for hard wire diameter up to 2.2mm and medium wire diameter up to 3.2 mm. The cutting edges are separately induction hardened for durabilty and longer working life and are hardend to approximately 61HRC. The jaws are angled at 40° and are ideal for use on electronic or tight to reach areas on computers, circuitry, or motor vehicles applications. Knipex have used a good quality special tool steel material that is oil hardened. Hard wire diameter: 2.2 mm.Medium wire diameter: 3.2 mm.Hardness approx. 61HRC.Length. 200 mm.
These Forgefix Carriage Bolts are Zinc Plated, and ideal for timber to timber joining. They come complete with a hex nut and are fully threaded to 100mm. Also known as 'Cup Square Hex Bolts', the square underneath the Cup stops rotation of the bolt when tightening. Conform to DIN 603 and DIN 934 standards. Available in a comprehensive range of sizes to suit most applications. APPLICATIONUsed mainly for fastening timber to timber and is extensively used for timber joist construction in house building and numerous decking applications. A Carriage Bolt, also known as a Coach Bolt or as a ‘Fully Threaded Cup Square Hex Bolt’, has a domed or countersunk head, and the shank is topped by a short square section under the head. The square section grips into the part being fixed (typically wood), preventing the bolt from turning when the nut is tightened. A rib neck Carriage Bolt has several longitudinal ribs instead of the square section, to grip into a metal part being fixed. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers.Carriage Bolt & Nut ZP M10 x 50 Bag 10
These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency. The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved. Ideal for wire harness work, and standard printed circuit board assembly. Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.Length (A): 125mm (5 in). Blade length (B): 16mm (0.63 in). Head width (C): 16mm (0.63 in). Head depth (D): 8mm (0.31 in). Tip width: (F): 1.6mm (0.06 in). Cutting capacity: 0.4-2.0mm. Cutting edge: Micro-bevel. The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are ‘pinched’, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.
This BlueSpot Tools Magnetic 7.5m/25ft Pocket Tape has a steel blade with easy-to-read metric and imperial graduations. With a rubberised, impact resistant case for increased comfort. It is self-locking for ease of use and increased safety. With a magnetic end hook, ideal for trying to measure between metallic surfaces.
Using a staple gun shouldn’t be a workout. Rapid ALU Combi Tackers with Powercurve Technology™ were developed with a leading physiotherapist for up to 65% less effort. It’s not only easier to squeeze, it also perfectly matches the power of your hand. The patented 3-step force adjuster system lets the user decide for themselves how much power to deploy. Save effort on jobs with short leg lengths and turn up the power with a simple flip of the force adjuster when required. Save energy - Your own.The Rapid ALU940 Combi Tacker is a high quality, ergonomically designed tacker ideal for do-it-yourself work, for example labels, textiles, canvas and other fibred materials as well as fine wood trim around the house. It has a dual magazine which uses Rapid No. 140 staples 6-14mm and No. 8 brads 15mm. Made in Sweden, it has a strong and light aluminium exterior with an ergonomic design and comfortable soft grip areas and comes covered by a 3 year guarantee.
