Metabo SSW 18 LT Power Plus Impact Wrench 18 Volt 2 x 4.0Ah Li-Ion

Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S

Faithfull universal engineers metal working hammer, precision ground with hardened striking faces to withstand the rigours of all metal working applications. Manufactured in accordance to BS876. Fitted with a traditional hickory handle.Weight: 1130g (2.1/2lb)

Used in combination with screwsinks to prepare perfectly sized plugs to fill counterbored holes. For best performance power drill should be held in a stand. For a perfect grain match use an offcut from the timber being plugged. To ensure an acurate fit we suggest you use the same screwsink from the Faithfull brand. The set of 4 contains sizes No 6, 8, 10 and 12.Cuts Size 10 Plugs (10mm)

The Arctic Crack-It Shock Freeze Release Spray releases seized and corroded parts through shock freezing. The freeze action breaks the corrosion seal and allows the penetrant to reach the corroded area, releasing the seized items in 1-2 minutes. Also helps to prevent future corrosion and is completely bio-degradable. Lowest Operational Temperature: -45°C.

Record Irwin V150B Woodcraft Vice is lighter in construction than the standard woodworking vices, this useful portable vice can be attached to most working surfaces by means of a 2.1/4in capacity integral clamp. Provision is also made for the body to be screwed permanently to the bench if required. High quality cast body fitted with carefully aligned steel slide bars and main screw. Jaw Width. 150mm (6in).Jaw Opening: 115mm (4 1/2in).

All purpose rubber mallet, used by professional tradesmen in the automotive industry and in maintenance workshops. Also suitable for DIY tasks and applications where a steel head is unsuitable. Featuring self-locking handles to deliver a gentle but firm blow with little rebound. The wooden handle is contoured to provide a comfortable grip during use.Colour : BlackSize : 63mm (2.1/2in).Weight : 680g (24oz).Face : 63 mm.