Bahco 9035 Adjustable Wrench 300mm with 55mm Extra Wide Jaw

This Marshalltown Masons Line is made from twisted nylon that has been heat set after winding to increase stability. Not affected by mortar, oil or mildew and will not absorb water. Suitable for staking out sites, concrete and landscaping layout and brick/block laying. Made in the U.S.A1 x Marshalltown M632 Masons Line 76.2m (250ft) - Fluorescent Yellow

Master Lock classic brass padlocks are a tough and reliable security solution. The solid brass body has a modern diamond shaped design and a brushed finish. The extensive range of brass padlock options means there is a Master Lock brass padlock for just about any need. Each padlock has a solid body, hardened steel shackle and dual locking levers. A variety of multi-pack options, where all padlocks in the pack open with the same key (keyed alike) is also available. Padlocks are available with 4-pin, 5-pin or 6-pin cylinders and with a variety of shackle lengths for added security and for a wider range of possible application options. All Master Lock padlocks are supplied with a minimum of 2 keys and a Lifetime Warranty against mechanical failure. Suggested Uses: Gates, containers, storage units and sheds.The Master Lock 150EURT has the following specifications: 2 x 50 mm solid brass padlocks - 25mm hardneed steel shackle, 7mm diameter - 5-pins - keyed alike

Bahco 1-476 4in Key Files have a handle developed according to the scientific ERGO™ process. This set is perfect for fine filing and polishing jobs. The set contains one of each handled file: hand, warding, square, three square, half round and round. Supplied in a snap-shut plastic wallet with hanging hole. Type of cut: 3 Smooth.Blade Length: 100mm.

Paslode IM350+ Diamond point clipped head Nail packs with paper strip, supplied with Paslode Special Impulse gas fuel cells.FINISH: All Paslode nails are Chrome 6, cadmium and lead free and are available in five finishes to meet corrosion requirements.Bright: Economy and bright nails meet the Eurocode 5 requirements for applications in service class 1 (indoor) Specification - No coating.Galv Plus : Meet the Eurocode 5 requirements for applications in service class 1 and 2 (indoor and covered outdoor) Specification - Zn / Al alloy approx 15µm.Electro Galv : Meet the Eurocode 5 requirements for all applications in service class 1 and 2 (indoor and covered outdoor) Specification - Zn and chromate minimum 7µm.Hot Dipped Galv : Meet the Eurocode 5 requirements for all applications in service class 1, 2 and 3 (indoor, covered outdoor and outdoor) Specification - Zinc coating minimum 50µm Stainless Steel : Meet the Eurocode 5 requirements for all applications in service class 1, 2 and 3 (indoor, covered outdoor and outdoor) Specification - A2 according to AISI 304, and A4 according to AISI 316.SHANK: Smooth Shank: The standard nail, offering high shear value and lowest withdrawal resistance. Fixing across the grain. Fixing into end grain. Clenching applications. Specification - Number of centres will vary with shank diameter.Unilock Shank : Increases withdrawal resistance. Drives easier than ring shank fixing across the grain. Specification - The ringed parts have 24 rings per inch.Ring Shank : Provides the highest withdrawal resistance. Fixing across the grain. Specification - RPI (Rings Per Inch) vary from 16 to 32 depending on Specification.HEAD TYPES :Round Head : The head area is designed to maximise resistance to the head being pulled through Specification - Head size between 2.0 and 2.5 times wire diameter according to EC5Clipped Head : Increases number of nails per strip. The head area is designed to maximise resistance to the head being pulled through Specification - Head area corresponding to full round head area, according to EC5

These Facom 12-point OGV sockets have a 1/2 inch drive to fit 1/2 inch ratchets. They are high quality and ideal for tightening and loosening bolts, nuts and other fasteners.The sockets are available in a range of metric sizes.Performance: conform to ISO 2725-1, DIN 3124 and NF ISO 2725-1.The FCMS15 socket has the following specifications:Socket size: 15.0mm.Length: 36mm.Weight: 60g.

Stahlwille INHEX Extra long sockets have 1/2in square drive and are suitable for hexagon socket head head screws. They are manufactured from chrome alloy steel and are chrome plated. Manufactured to DIN 7422 (metric sizes). MADE IN GERMANY.Stahlwille In-Hex Socket 1/2in Drive Xtra Long. Size: 5mm.Overall length: 120mm.