IRWIN Record 200-45 Pipe Cutter is perfect for cutting plastic pipe with exceptionally thin cutting wheel and roller.It will also cut copper tube but its use should be confined to one or the other as cutting copper will reduce the effectiveness of the wheel on plastics. Die-cast body with stove enamelled rust resistant finish. Capacity: 15 to 45mm (9/16 to 1 3/4 in).
Number of drilling modes: Three. Hammer drill, rotary drill, hammer only. Rotary drilling with hammer support can be selected as can pure hammer-only action for heavy-duty breaking and chiselling. The HR3210C features the unique Makita AVT Anti Vibration Technology design employing the pneumatic pressure created in the drills hammer piston chamber to move a counter balance in the opposite direction to reduce the impact vibrations at the steel point. This dramatically reduces vibration Forward/reverse rotationVariable speed triggerTorque limiter3 functionRotary onlyRotary hammerHammer onlyDouble insulated Blows per Minute: 1,650-3,300bpmNo Load Speed: 315-630rpmInput Wattage: 850wMax Bit Diameter: 32mmMax Core Diameter: 90mmImpact Energy: HR310C: 5.6 JoulesHR3210FCT: 6.4 JoulesWeight:HR310C: 5.2kgHR3210FCT: 5.4kg Chuck type: SDS plusVibration drilling : 2.5 m/sec²Vibration hammer drilling: 10 m/sec²Vibration chiselling: 7 m/sec²Vibration K factor: 1.5 m/sec² Supplied with: Side handle, depth stop, bit grease, carry case. HR3210 FCT also supplied with Quick Change Chuck.
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S
Thor super plastic hammers have a malleable iron head fitted with cylindrical ultra-high molecular weight polythene faces which are designed to wear and be replaced. Available in 3 different weights. The ultra-high molecular weight polythene heads provide high impact, durability and high abrasive resistance. The faces will not fracture, splinter or delaminate. Ideal for use as a general-purpose, soft-faced hammer in engineering applications for assembly, repair and maintenance operations as an alternative to a rawhide faced hammer. Size: 2.Weight 790g (1 3/4lb).Diameter 38mm (1 1/2 in).
Featuring a back lit LCD screen with optional wide and narrow accuracy settings the easily usable line laser detector has a working range up to 50 metres, whilst the included heavy duty clamp can simply mount onto a grade rod.
