Held Nela, textile pant women

MR. JUMP, the fiber helmet studied in details for comfort, technology and for sure safety for end user. It has been studied and tested to optimize the outside and inside air flows.
OUTER SHELL in tricarboco material, mix of Kevlar, carbon and fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell sizes: XS-L and XL-2XL
INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M and L). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation.
The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding.
MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471
CHEEK PADS completely removable and washable, with different thickness to get a perfect customization od the helmet.
INTERNAL SHELL completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet and to let off the hot air through the back part.
INNER (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper and back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation.
The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses.
weigth: ca. 1000gr

Outer garment
Fibretech 500D, soft & stong fabric Softshell panels Armex : high resistance to abrasion on forearm
Membrane
Waterproof & breathable membrane
Isolation
120 g. removable thermo-alu lining
Protection
Adjustable approved elbow protectors Approved shoulder protectors Pocket for approved back protector
Comfort
Regular fit Fixed mesh lining Anti-flutter system on sleeves Cuff fastening Jacket bottom tightening by elastic cord and stopper High comfort collar Reflective material Zip for connecting with trousers 2 outer pockets 1 back pocket 3 inner pockets Puls Air ventilation system Fitex system waist fastening

BMW F 650 GS Bj. 04-07 / nicht in Kombination mit Original Handschutz 395 mm hoch - 440 mm breit, mit Kantenschutz ABE 38743 12,5 cm höher als die Originale ersetzt die Original Scheibe ABE-Heft: ABE-Heft-0380839001379341296.pdfAnbauanleitung: Anbau-0393829001379341296.pdfABE:ABE-0222195001382476166.pdf - GIVI D331STG Spezifisches Windschild Transparent

Visior for following Shark helmets
Evoline Series 3 Evoline Evoline Pro Carbon
*example picture

Material
CORDURA® Comfort elasticated fabric Tutu cowhide leather
Ergonomics
Jacket-pants fastening system Waist adjustment
Performance shock
Adjustable and removable composite protectors certified to EN 1621.1 Standard on shoulders Composite protectors certified to EN 1621.1 Standard on elbows Floating sport shoulder construction with replaceable aluminum plate Pocket for G1 & G2 back protector Replaceable aluminum plate on shoulder
Temperature adjustment
Air vents on sides Nanofeel® liner with Silver ion treatment
General features
2 outer pockets prEN 17092 motorbike protective jacket Reflective inserts

General Features
Micrometrically adjustable strap retention system
Visor
Integrated non-scratch ISV-5-1 sun visor (sizes XS-S) and ISV-5-2 (sizes M-L-XL) City 18-1 non-scratch visor 1 (sizes XS-S) and City 18-2 (sizes M-L-XL). It covers and protects the face to below the level of the chin New SUN VISOR CONTROL mechanism for operating sun visor. The visor is operated by turning the plate on the left side of the helmet.
Exterior and interior shell
HIR-TH (High Resistance Thermoplastic Resin) outer shell Inner shell in EPS in 4 sizes, shell and EPS dimensions optimised using the FEM (Finite Elements Analysis) system 2 external shell sizes Inner EPS in two sizes with different densities
Interiors
Fully removable and washable Dry Comfort inner liners
Ventialtion
Central air vents integrated into the shell profile for optimal ventilation
Functionality
Removable neck roll