Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S
Stahlwille reversible, fine tooth Ratchet Insert Tool with 60 teeth. Long-term loading of the input and output square drive is in accordance with DIN EN ISO 6789:2003. NOTE: Please pay attention to insert size required - 9 x 12 or 14 x 18.CAUTION: A modified torque setting is required if using the size 40HD. MADE IN GERMANY.Stahlwille Ratchet Insert Tool. Size: 9 x 12mm.Drive: 3/8 in.
The UNION Hercules 1K57 padlock, has a vertical sliding shackle which comes through the staple hole making direct attack impossible. Insurance Graded CEN6 and accredited Sold Secure Gold, this lock is ideal fo use in commercial or high security applications. Supplied with 3 keys AVA Available with AVA 10 discKey retention when the padlock is unlockedHardened steel unsprung shackleSuitable for use with UNION 7B018 padbar Anti DrillAnti SawForce ResistantAnti PickTorque ResistantCorrosion Resistant Specification:Shackle type - ConcealedShackle diameter - 16mmShackle clearance - N/ALocking mechanism - Key
Useful for laying out and scribing circles beyond the capacity of ordinary dividers. Clamping device firmly holds points, which can be replaced with a pencil. The heads will accommodate a beam up to 9.5mm (3/8in) thick and 19mm (3/4in) wide. Beam is not supplied. 2 Trammel heads, 2 small points 150mm (6in).
IRWIN Record Mini Bender 210 (3, 4 & 6mm Copper) is designed for bending small diameter copper, stainless steel, aluminium and steel tubes.Particularly suitable for the hydraulic engineer, vehicle mechanic and tool maker.Capacity: 3, 4, and 6mm (1/8, 3/16, and 1/4in) O.D.
These heavy-duty toolboxes are ideal for use on the worksite, garage or around the home. They have a centre galvanised finish, this gives the toolbox a sturdy durable construction and is also rust-resistant, as are the two heavy-duty metal latches. They have a removable plastic tray which is ideal for smaller tools like screwdrivers, spanners etc, or tapes and fixings that can be found at a glance. The lid incorporates a saw groove for holding pipes and timber for cutting when there is no work bench available. The lid on has a honeycomb design to give it extra strength and durability, and the soft grip handle folds flat in to the lid when not in use.Dimensions: 662 x 293 x 222mm.
