Free
Support
Merlin Elmhurst Motorrad WachsjackeEigenschaften:Eine einzigartige Kombination aus Halley Stevensons® schottisch gewachster Baumwolle und der thermischen Outlast® Innenfutter-Technologie 8oz trocken (12oz nass) Halley Stevensons®, schottisch gewachste Baumwolle Preisgekröntes abnehmbares Outlast® 'Universe' thermoregulierendes Innenfutter Reissa® Active wasserdichte und atmungsaktive Membran Sicherheitsgeprüfte Schulter- und Ellenbogenprotektor mit sicherheitsgeprüftem Rückenprotektor Erweiterung der hinteren Schulterplatten für mehr Flexibilität und Komfort YKK®-Reißverschlüsse mit durchgehendem Antik-Finish Merlin-Druckknöpfe Mehrere Taschen (ein und aus) und Einstellpunkte Kurze YKK®- Jacke zu Hose Verbindungsreißverschluss
Specification:Name: 30W Solar Panel Semi-flexible Portable Car And Ship Emergency Charging BoardModel: B49715Solar Panel:Max.Power (Pmax): 30WMax. Power Voltage (Vmp): 18VMax.Power Current (Imp): 1.2ANumber of Cells: 6pcsOutput: USB 5VDC 18VWorking Temperature: -35~60℃Solar Panel Size:approx.42cm x 37cmWeight:approx. 529gSolar Charger Controller:Rated Voltage:12/24VRated Current :10AMax. PV Voltage: 50VMax. PV Input Power:130W(12V);260W(24V)Size:approx. 13.2cm x 3.3cm x 6.7cmWeight:approx. 133gFeatures:- Light weight- Environmental protection, free power from the sun, go green!- High transformation efficiency, our polycrystalline silicon efficiency can up to 20 percent.- Light and Thin, easy to use and carry.- The Charging temperature is -35 - +60C centigrade.- Flexible Solar Panel, A maximum 30 arc bendable.- Surge protection technology keep you and your devices safe.- Durable, water-resistant and long lifespan.- Wide application, suitable for laptops, Car Batteries, Car, RV, Boat, Ship, Aircraft, Satellites, Space Stations, outdoor breeding, planting, tourism, solar street lamp.Application:1. Dual output, can output 5V 1200ma, can also output 18V 1.2A2. It can be used for 5v DC power supply products of mobile phones, and can also charge the battery of the vehicle and boat.3. Light weight, easy to carry, can also absorb glass surface, can also be buckled in travel bags, etc.4. Suitable for outdoor mountain climbers, you can also supply power to the outdoor pump, and also p
MR. JUMP, the fiber helmet studied in details for comfort, technology and for sure safety for end user. It has been studied and tested to optimize the outside and inside air flows.
OUTER SHELL in tricarboco material, mix of Kevlar, carbon and fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell sizes: XS-L and XL-2XL
INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M and L). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation.
The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding.
MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471
CHEEK PADS completely removable and washable, with different thickness to get a perfect customization od the helmet.
INTERNAL SHELL completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet and to let off the hot air through the back part.
INNER (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper and back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation.
The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses.
weigth: ca. 1000gr
Features
knee protectors hip protectors Fixed cotton lining Height adjustable knee protectors Bottomleg removable elastics Different leg lengths available
AC³ (Aqua, Cold, Crash, Comfort)
Aqua: 1 of 5 points Cold: 1 of 5 points Crash: 4 of 5 points Comfort: 5 of 5 points
point system on manufacturer base.
Features
Classic collar Adjustable cuffs with gusset and strap Adjustement Buckle on waist Press-stud on biceps Bottom with gusset and strap 4 external pockets, 4 internal pockets, 1 waterproof wallet pocket Connection with trousers thanks to small zip on back + loop
Safety
Certified Elbow-shoulder protectors. Level 2 Back protector pocket Reflective material on back
Material
Noxiguard 600D Drymesh 3/2
Acerbis X-Factory HandschützerGeschlossener Handschutz Stahlbar auf der Oberfläche in verschiedenen Farben gedruckt Anticorodalarmbänder, um den Handschutz am Lenker zu befestigen Stahlexpander für engere Befestigung und gegen Drehung im Falle eines Aufpralls Doppel-Injektionsabdeckungen Anwendung: auf Lenker mit Innendurchmesser von 13,5 mm bis 16 mm und Außendurchmesser von 22 mm bis 28 mm
