Free
Support
302-53W-12P Spare blades for 302 and 502 fret saws. Suitable for cutting wood. Length: 130mm (5.1/8in).Grade: Fine.Pack of 12.
Miniatura de aluminio pequeña Hobby Clamp en mesa Mini herramienta multifuncional
The Faithfull set of two spokeshaves, 1 concave and 1 convex, made with malleable iron bodies. A concave spokeshave is ideal for shaping spindles, oars, chair and table legs. A convex spokeshave is used for recessed work. Cutter Width: 50mm. Length: 240mm.
These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency. The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved. Ideal for wire harness work, and standard printed circuit board assembly. Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.Length (A): 125mm (5 in). Blade length (B): 16mm (0.63 in). Head width (C): 16mm (0.63 in). Head depth (D): 8mm (0.31 in). Tip width: (F): 1.6mm (0.06 in). Cutting capacity: 0.4-2.0mm. Cutting edge: Micro-bevel. The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are ‘pinched’, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.
Paslode IM350+ Diamond point clipped head Nail packs with paper strip, supplied with Paslode Special Impulse gas fuel cells.FINISH: All Paslode nails are Chrome 6, cadmium and lead free and are available in five finishes to meet corrosion requirements.Bright: Economy and bright nails meet the Eurocode 5 requirements for applications in service class 1 (indoor) Specification - No coating.Galv Plus : Meet the Eurocode 5 requirements for applications in service class 1 and 2 (indoor and covered outdoor) Specification - Zn / Al alloy approx 15µm.Electro Galv : Meet the Eurocode 5 requirements for all applications in service class 1 and 2 (indoor and covered outdoor) Specification - Zn and chromate minimum 7µm.Hot Dipped Galv : Meet the Eurocode 5 requirements for all applications in service class 1, 2 and 3 (indoor, covered outdoor and outdoor) Specification - Zinc coating minimum 50µm Stainless Steel : Meet the Eurocode 5 requirements for all applications in service class 1, 2 and 3 (indoor, covered outdoor and outdoor) Specification - A2 according to AISI 304, and A4 according to AISI 316.SHANK: Smooth Shank: The standard nail, offering high shear value and lowest withdrawal resistance. Fixing across the grain. Fixing into end grain. Clenching applications. Specification - Number of centres will vary with shank diameter.Unilock Shank : Increases withdrawal resistance. Drives easier than ring shank fixing across the grain. Specification - The ringed parts have 24 rings per inch.Ring Shank : Provides the highest withdrawal resistance. Fixing across the grain. Specification - RPI (Rings Per Inch) vary from 16 to 32 depending on Specification.HEAD TYPES :Round Head : The head area is designed to maximise resistance to the head being pulled through Specification - Head size between 2.0 and 2.5 times wire diameter according to EC5Clipped Head : Increases number of nails per strip. The head area is designed to maximise resistance to the head being pulled through Specification - Head area corresponding to full round head area, according to EC5
The ALM Manufacturing Replacement Chainsaw Chains to fit a wide range of chainsaw makes and models.The ALMCH066 Chainsaw Chain has a 3/8 inch Low profile (L/P), 0.043in guidebar slot 0.325 mm and Low profile (L/P) 1.1 mm guidebar slot.This chain is made to fit the Ryobi range and suit saws with a 40cm bar and chain with 66 drive links including:PCN-3840, PCN-4040.