Faithfull Nail punch with a square head which provides a larger striking area and stops the punch rolling off the bench. Accurately hardened and tempered with a precision formed concave tip for better nail contact. Designed to drive nail heads below the surface of the wood.Point Diameter: 4.0mm (5/32in)Length: 100mm (4in)
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S
The Paslode IM65 F16 Angled 16 Gauge Brad Nailer for all second fix applications. Improved design featuring key benefits such as an open magazine for easy brad viewing, and a vastly improved line of sight to enable increased accuracy during fixing. Fitted with a no-mar tip for accurate placement and reduced damage to the wood. Quick charge battery with an improved on/off battery system, the new quick charge, long life Lithium battery fires up to 6,000 brads on a single charge (1 hour); 200 brads in just 2 minutes charge. Quick start up with no power cables or air hoses required, the tools improve efficiency and safety in all environments against pneumatic tools. It offers optimal balance, allowing any user to manoeuvre into tight spaces and work all day long without fatigue. Keep one hand free with the improved belt hook design. Consistent finishing due to an improved adjustable depth of drive system, the tool allows seamless fixing without the extra time and cost of re-touching and re-finishing work. Supplied with: 2 x Li-Ion Batteries, 1 x Charger, 1 x High Impact Carry Case, 1 x 32mm Brad Pack, 1 x 38mm Brad Pack, 1 x 51mm Brad Pack and 1 x Cleaning Kit. Specification: Magazine Capacity: 100 Brads. Fires: Nail Length 16-63mm. Cycle Rate: 2-3 Brads/Second. Max Cycle: 1,000 Brads/Hour; 4,000 brads/day. Fuel Cell: Approx. 1,000 Shots. Battery: Lithium 1.25Ah: Up to 6,000 Shots. Charge Time: 1 Hour Max. Dimensions: 301 x 288 x 90mm. Weight: 2.1kg.
The Makita 9920 Belt Sander has the following features:- Variable speed control.- Constant speed under load.- High power for stock removal.- Flat top for inverted applications.- Dust bag.- Long cable for sanding runs.- Double insulated. Technical specifications:Belt Size: 76 x 610mm.Belt Speed: 210 - 440m/min.Power rating: 1,010 watt.Vibration sanding: 2.5m/sec².Vibration K factor: 1.5m/sec².Noise sound power: 96 dB(A).Noise sound pressure : 85 dB(A).Noise K factor: 3 dB(A).Net weight: 4.5kg. Supplied with:Abrasive belt.Cork/carbon pad.Dust bag.The Makita MAK9920 Belt Sander Variable Speed uses 240 volt.
The Thor hardwood mallets have a laminated cylindrical compressed wood heads (to a density of 1.3) fitted with flushed-in glass fibre hoops for extra security. The mallets have a conical self-locking handle and come in 3 different weights. These have an excellent resistance to impact and will give a long service life, they are suitable for hot work applications. Typical uses for these mallets include steel plate trade, casting, schools and technical colleges, general assembly, aluminium forming, aviation etc.Weight: 750g (1 3/4lb).Diameter: 67 mm (2 3/4in).
Evolution's Electric Disc Cutter easily cuts Concrete, Stone, Brick, and Paving, even reinforced concrete, with the supplied diamond blade.The powerful 2400W motor makes easy work of the most robust materials and because it is electric there are no harmful fumes, making it ideal for work in enclosed areas.The ergonomic support handles are ideally positioned for perfect balance when cutting and the spindle lock mechanism means blade replacement is quick and simple.Technical Specifications:Motor: 2400WSpeed: 5000/minDisc Diameter: 305mmDisc Thickness: 2.0mmBore Diameter: 20 / 22mmDisc Weight: 1.78kgMax Cutting Depth: 100mmMachine Weight: 9.5kgProduct Dimensions: 464x575x390mmRecommended Maximum Duty Cycle: 20minsSound Pressure Level (Under Load): 102.4dB(A)Vibration Level: 4.8m/s2Gross Weight: 11.82kgIncludes:Dust Extraction PortSpannerOperator's Manual1 x Blade
