Screw Cup Washers - Brass No.8 (Pack 20)

The Kew Nilfisk Alto Powerspeed Nozzle has a spinning pencil jet that increases both the speed of cleaning and the area that can be cleaned in one pass. It blasts dirt away and is ideal for cleaning heavily soiled areas. Can be used with Nilfisk C100, C105, C110, C120, E130 and E140 pressure washers.

The Henry Squire Leopard Range offers a finely shaped solid brass case to give a slimmer profile. Pin tumbler mechanism and stainless steel springs. Good general security locks for internal and external use. Hardened steel shackles on padlocks 25-60mm. Keyed alike 20-60mm available to order.

The Wera Slotted 160i VDE insulated screwdrivers are tested individually for dielectric strength under a load of 10,000 volts so as to ensure safe working with loads up to 1,000 volts. They have a premium lasertip which is a laser roughened surface that literally bites into the screwhead, reducing cam out. With patented ergonomic, multi component Kraftform handle which uniquely fits to the shape of the hand during screwdriver use. Please note: WER006100 does not have a Lasertip.Blade Length, 150mmTip, 6.5mm

Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S

The DEWALT D25133K SDS 3 Mode Hammer Drill is ideal for drilling anchor and fixing holes into concrete and masonry from 4 to 26mm in diameter. It has a rotation-stop mode for light chiselling applications in brick, soft masonry and occasionally concrete. It also features an impact-stop mode for drilling in wood, steel, ceramic and screwdriving applications. The drill has a mechanical clutch that eliminates sudden high-torque reaction, should the bit jam. It features electronic variable speed for total control in any application. The ergonomic rubber coated back handle and industrial design provides easy and comfortable handling in any application. Suitable for the following applications: Drilling holes in solid masonry, concrete and stone from 4 to 26mm in diameter to various fixing. Drilling through holes in masonry to house pipes and cables. Light chipping in brick or masonry Tile removal from kitchens and bathrooms. Small channelling in brick. Mortar and plaster removal. Some drilling in wood and steel. Specifications: Mode: Rotary, SDS Hammer, Chisel Only. Input Power: 800 Watt. No Load Speed: 0-1,500/min. Impact Rate: 0-5,550/bpm 2.6 Joules. Capacity: Wood: 30mm, Steel: 13mm, Concrete 26mm, Core: 50mm. Toolholder: SDS-Plus. Weight: 2.3kg.

SB-3732 series nail punches are manufactured with a plastic handle and fully polished steel surface with a brilliant chrome finish.Tip size: 2.0 mm (5/64in). Length: 125 mm (5in).