DeWalt DNPT31R90 Galvanised 33ﾰ Angle Ring Shank Nails 3.1 x 90mm (2200)

Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S

Faithfull heavy-duty clamps manufactured from a high quality carbon steel bar with large malleable iron clamping heads. Clamp bars have a Black Oxide coating with powder coated heads for complete rust protection. Other features include a high grade steel mainscrew with a wear resistant Acme thread, which applies pressure quickly and smoothly. Tail slides are easily adjusted and secured by a steel pin passing through one of the locating holes. Tail slide and heads are flat bottomed so that the clamp can stand upright without support.

The IRWIN Jack Xpert range of handsaws have evolved into super-efficient cutting tools that have University verified technology at their heart. This triple-ground tooth technology (TGT) not only increases efficiency but also optimises cutting performance on both the push and pull strokes - so you dont have to work so hard. Hardpoint tenon saw with soft-grip handle for user comfort. The ideal choice for fine carpentry and can be used with a mitre box.Size: 300mm (12 in).Teeth 12 tpi

The Faithfull 4-Sided 62mm replacment blade for use with the FAI WS624 wood scraper.

Bahco S138 1/4in, 3/8in, and 1/2in drive 138 piece metric and imperial socket set that consists of: 12 x 1/4in Hexagon Sockets: 4, 4.5, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, and 13mm. 10 x 1/4in Hexagon Deep Sockets: 4, 5, 6, 7, 8, 9, 10, 11, 12, and 13mm. 1 x 1/4in Reversible Ratchet 60 Teeth and Two Component Handle 150mm. 1 x 1/4in Spinner Handle with Two Component Handle 150mm. 1 x 1/4in Sliding T-bar 106mm, 1 x 1/4in Extension Bar 50mm, 1 x 1/4in Extension Bar 100mm, 1 x 1/4in Universal Joint, 1 x 1/4in Bit Holder, and 1 x 1/4in Flexible Extension Bar 150mm. 16 x 3/8in Hexagon Sockets: 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 21, and 22mm. 1 x 3/8in Reversible Ratchet 60 Teeth and Two Component Handle 200mm. 1 x 3/8in Spark Plug Socket 21mm (13/16in), 1 x 3/8in Spark Plug Socket 18mm, 1 x 3/8in Spark Plug Socket 16mm (5/8in), 1 x 3/8in Universal Joint, 1 x 3/8in Extension Bar 75mm, and 1 x 3/8in Extension Bar 150mm. 18 x 1/2in Hexagon Sockets: 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 27, 32, and 34mm. 9 x 1/2in Hexagon Sockets: 3/8, 7/16, 1/2, 9/16, 11/16, 3/4, 13/16, 7/8, and 1.3/16in. 1 x 1/2in Reversible Ratchet With 60 Teeth and Two Component Handle 250mm, 1 x 1/2in Sliding T-bar With Double Function, 1/2in Head 3/8F-1/2in Male Adaptor, 1 x 1/2in Extension Bar 125mm, 1 x 1/2in Extension Bar 250mm, and 1 x 1/2in Universal joint. 1 x Bits Adaptor: 1/4in Square Drive. 4 x Pozidriv Bits: PZ 0, 1, 2, and 3. 5 x Phillips Bits: PH 0, 1, 2, 3, and 4. 3 x Flat Bits: 4, 5.5, and 7mm. 6 x Insert Bits: 3, 4, 5, 6, 8, and 10mm. 9 x Torx Bits: T 8, 10, 15, 20, 25, 27, 30, 40, and 45. 1 x Bits Ratchet, 3 x Hexagon Keys: 1.5, 2, and 2.5mm. 8 x Crow Foot Wrenches: 10, 11, 13, 14, 15, 17, 18, and19mm 13 x Combination Spanners: 7, 8, 9, 10, 11, 12, 13, 14, 15,16, 17, 18, and 19mm. Supplied in a High Density Polythene Case.

TNI-U TU-6301E trinquete cortador tubo de PVC alta calidad tubería de plástico y tubería cortador Dual colores maneja herramienta cortante