A slim open ended spanner designed, manufactured and tested in accordance with ISO 9002 with 15° angled heads. Chrome vanadium. Satin finish. DIN3110Size 8 x 9mmLength 140mm
This hacking knife has a steel blade with twin leather scales riveted to the shaft. It can be struck with a hammer to remove old putty from window frames. Size: 4.1/2in.
Paslode IM350+ Diamond point clipped head Nail packs with paper strip, supplied with Paslode Special Impulse gas fuel cells.FINISH: All Paslode nails are Chrome 6, cadmium and lead free and are available in five finishes to meet corrosion requirements.Bright: Economy and bright nails meet the Eurocode 5 requirements for applications in service class 1 (indoor) Specification - No coating.Galv Plus : Meet the Eurocode 5 requirements for applications in service class 1 and 2 (indoor and covered outdoor) Specification - Zn / Al alloy approx 15µm.Electro Galv : Meet the Eurocode 5 requirements for all applications in service class 1 and 2 (indoor and covered outdoor) Specification - Zn and chromate minimum 7µm.Hot Dipped Galv : Meet the Eurocode 5 requirements for all applications in service class 1, 2 and 3 (indoor, covered outdoor and outdoor) Specification - Zinc coating minimum 50µm Stainless Steel : Meet the Eurocode 5 requirements for all applications in service class 1, 2 and 3 (indoor, covered outdoor and outdoor) Specification - A2 according to AISI 304, and A4 according to AISI 316.SHANK: Smooth Shank: The standard nail, offering high shear value and lowest withdrawal resistance. Fixing across the grain. Fixing into end grain. Clenching applications. Specification - Number of centres will vary with shank diameter.Unilock Shank : Increases withdrawal resistance. Drives easier than ring shank fixing across the grain. Specification - The ringed parts have 24 rings per inch.Ring Shank : Provides the highest withdrawal resistance. Fixing across the grain. Specification - RPI (Rings Per Inch) vary from 16 to 32 depending on Specification.HEAD TYPES :Round Head : The head area is designed to maximise resistance to the head being pulled through Specification - Head size between 2.0 and 2.5 times wire diameter according to EC5Clipped Head : Increases number of nails per strip. The head area is designed to maximise resistance to the head being pulled through Specification - Head area corresponding to full round head area, according to EC5
The ABUS 65 Series brass padlocks have a body which is made from solid brass, hardened steel shackle up to 30mm and hardened steel alloy shackle 40mm and above. The inner components are made from non-corrosive materials. The precision pin cylinder has mushroom counter pins with the paracentric key-way offering greater protection against manipulation. They are suitable for low to medium security requirements and are also suitable where a strong requirement for service performance and longevity is required. The padlock locking is automatic, it does not require a key.The cylinder can be re-keyed to match an existing key (Keyed Alike). Overall width: 50 mmOverall height: 77 mmOverall depth: 18 mm Shackle width: 28 mm I.D.Shckle height: 29 mmShackle Dia: 8 mm
The Knipex 74 91 Series high leverage centre cutters with dipped PVC handles and centric precision cutting edges with an integrated forged joint axle for heavy-duty use. High cutting performance with minimum effort due to optimum co-ordination of the cutting edge angle, transmission ratio and ergonomic handle shape. Like most of the Knipex range, these cutters are oil hardened and tempered for longer life, with cutting edges separately induction-hardened to approx. 64hrc. They are made from top quality high grade Chrome Vanadium tool steel with polished hardened heads. Specification Cutting Capacity: Piano: 3.5mm, Hard: 3.8mm, Medium: 5.0mm.Length: 250mm (10in).
