Sexy Deep V Printed Criss Cross Backless Bikini

To have a maximum safety the helmet must fit tightly and be correctly and securely fastened, in order not to be able to be taken off neither by pulling it nor by rotating it around the head. If it is too big, it may slide down over the eyes or turn in a lateral direction due to movement during riding, blocking the right visibility. Safety Shell in three sizes (M, L and XL) hand made. The new material is a mix of carbon and aramidic fabric.
Internal Polystyrene in three sizes (M, L and XL). The special shape and construction in different density increases mechanical resistance in the event of accidental shock.
Shield thermoformed froma flat sheet. Each shield is a one-of-a-kind piece with unequalled optical features and mechanical resistance. Thanks to this process, the face shield is anti scratch and anti fog and there is no need to use additional lenses on the visor.
The D-Ring Retention System has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding. ECE 22-05 Comfort Cheekpads completely removable and washable, in different thicknesses for a complete customization of the product. Internal Shell completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in teh internal part of teh helmet and to let off the hot air through the back part.
Inner (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA.
Removeable Nose Protector Ventilation
The Shell is a polystyrene with channels for inside air flows. In the front part there is a Air Ventilation with on/off system, which gets the internal helmet ventilation. On the chin part there is an adjustable Air Ventilation.
Aerodynamics Spoiler and Back Air Ventilation: produced in polycarbonate , it has been studied and tested in wind tunnel, so that the point of detachment of the aerodynamic flow is shifted as far away as possible from the shell. This results in less turbulence and therefore fewer vibrations on the helmet itself. This helmet comes standard with a clear visor.

General Features
Micrometrically adjustable strap retention system
Visor
Integrated non-scratch ISV-5-1 sun visor (sizes XS-S) and ISV-5-2 (sizes M-L-XL) City 18-1 non-scratch visor 1 (sizes XS-S) and City 18-2 (sizes M-L-XL). It covers and protects the face to below the level of the chin New SUN VISOR CONTROL mechanism for operating sun visor. The visor is operated by turning the plate on the left side of the helmet.
Exterior and interior shell
HIR-TH (High Resistance Thermoplastic Resin) outer shell Inner shell in EPS in 4 sizes, shell and EPS dimensions optimised using the FEM (Finite Elements Analysis) system 2 external shell sizes Inner EPS in two sizes with different densities
Interiors
Fully removable and washable Dry Comfort inner liners
Ventialtion
Central air vents integrated into the shell profile for optimal ventilation
Functionality
Removable neck roll

Features
Waterproof and breathable thanks to the soltoTEX® membrane Textile lining Comfort foot bed 2 zippers to make it easier to put on the boots Reinforced heel cap Stretch insert on the calf Inner boot with neoprene on the top for more comfort Reflective insert on the heel Plastic inlays on ankle and shin section Abrasion-proof rubber sole Gear lever protection made of rubber Safety: in accordance with the standard EN13634:2015

CarWindscreen Washer BottleMotor Male Plug NewFor Nissan Navara D22 Ute 1997-2012Specification:-Type: Washer Bottle-Color:White-Manufacturer Part Number:W01-77719105-0Feature:-Windscreen washer bottle assembly with narrow plug type.-Direct Replacement Bottle with cap.-Excellent Fitment and Quality.-Correct Connector No cutting or splicing.-Strict quality control standards to Build and test.*Instruction Not Included, Professional Installation Is Highly Recommended.*Fitment:For Nissan Navara D22 Ute 1997-2012Note:-Please allow 1-3mm differs due to manual measurement.-Due to the different display and different light, the picture may not reflect the actual color of the item. Thanks for your understanding.Package Included:1x Windscreen Washer BottleFitment:For Nissan Navara D22 Ute 1997-2012

Description:Be durable and practical.Be of all new and high quality.Built to strict quality control standards.Fitted for 12V battery installation motorcycles,motorbike,scooter.Output circuit and overload, reverse polarity and multiple protection, safe to use.Specification:Product Name: Motorcycle Ignition SwitchMaterial: Aluminum/PlasticWeight: 310gCurrent: 5AVoltage: 12VPower: 60WSize: 11*5.5/4.32.2inchDiameter: 3.2cm/1.3inch,2.7cm/1.1inchWire length: 29cm/11.4inchColor: BlackFitment:Fit for Yamaha YBR 125 2007-2014Package Included:1 X Motorcycle Ignition Switch2 X Keys

Taillight Rear Right Side Tail Lamp Bumper Cover for Audi Q5 2.0T 2009-2016 8R0945096Feature:Perfect to replace your old model.New Stylish design, make your car more fashion.Durable, undamaged.Easy to install, just plugplay.Description:-Shell Color: Red-Light Color: Yellow-Material: Arcylonitrile Butadine Styrene Plastic-Placement on Vehicle: Rear Right-Size: 53.7x5x9.5cm/21.14x1.97x3.74-Quantity: 1 pc-Other Part Number: 8R0945096 8R0945096B 8RD 945 096 8RD945096Fitment:for Audi Q5 2009-2016NOTE:-No Bulbs Included-Pls confirm the fit item if it matches your models before you purchase.-No install instruction included. Professional installation is highly recomended!Package Included:1 x Rear Right Light (Bulbs Not included)