Abus 92/65 Monoblock Shutter Padlock Carded

The DEWALT DCK206M2 Twin Pack, contains the following: 1 x 18 Volt DCH253 3 Mode SDS Hammer Drill that is ideal for drilling anchors and fixing holes into concrete, brick and masonry from 4mm to 24mm. The hammer drill has a rotation stop mode for light chiselling in plaster, tiles and render and an impact stop mode for rotary only drilling in wood and metal. It uses 4.0Ah 18 Volt Lithium Ion batteries to deliver high performance, long life and maximum runtime. No Load Speed: 0-1,200/min.Impact Rate: 0-4,500/min with 2.1 Joules.Capacity: Concrete: 24mm, Steel: 13mm, Wood: 26mm.Weight 3.1kg. 1 x 18 Volt DCD785 XR Compact Hammer Drill Driver has an ultra compact, lightweight design that allows it to be used in confined spaces, whilst the intelligent trigger design allows for total control of application. It has a two speed, all metal transmission for increased run time and a longer tool life. Chuck: 13mm Keyless.No Load Speed: 0-600/0-2,000/min.Impact Rate: 0-10,200/0-34,000/bpmTorque: 60Nm, 14 Settings.Capacity: Steel: 13mm, Masonry: 13mm, Wood: 38mm 1 x 10.8-18 Volt DCB105 Multi-Voltage XR Charger varies the charge rate according to battery type to increase battery pack life. It features diagnostics with bright LEDindicator which communicates the battery charge status: charged, charging, power problem, and battery too hot or too cold. Charges all XR Li-Ion DEWALT Slide Pack 10.8, 14.4, and 18 Volt batteries.

The Plantpak Half Propagator Lids are suitable for use with the Half Seed Trays (PPK70200006). They are lightweight, durable and allow in maximum light whilst retaining optimum heat and humidity within the growing environment. Supplied in packs of 50.

These Forgefix Set Screws are made from grade 8.8 steel and are zinc plated for increased resistance to corrosion. They are fully threaded and conform to DIN 933 standards.Can be used with many Nut types and washers. APPLICATION:For fastening together numerous types of material or to be fastened in to pre-tapped holes.Widely used in many engineering applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers.High Tensile Set Screw Zinc Plated M10 x 30 Bag 10

Steel scale in hardened stainless steel with matt chrome-plated surface for anti-glare reading. Graduated in millimetres along the upper edge, and half millimetres on lower edge. The reverse side is blank. Manufactured in hardened stainless steel for extra durability, graduated in millimetres on the upper edge, half millimetres on the lower edge and decimetre figures in red with a tolerance ± 0.3mmLength: 1000mm (39 in)Width: 35mmThickness: 1.5mm

ABUS Diskus 26 series padlocks have a pin tumbler cylinder with anti-pick mushroom pins, a solid lock body which resists drill, pull & manipulation attacks, and a through hardened steel alloy shackle to resist saw attacks.'Deep Weld Technology' which offers maximum case strength. Where to use it: High security requirement in severe weather conditions The shackle is manufactured from hardened steel alloy and is protected in a stainless steel body. Key operated, key retaining (a key is needed for locking. Lock retains key until locked) The anti-cut plate provides 360 degree protection from sawing while a top quality welded seam secures against impact attack. Overall diameter: 71 mmOverall depth: 30 mm Shackle width: 19.5 mm I.D.Shackle height: 17 mmShackle Dia: 10 mm

Blank key to suit 85 Series Padlocks.85/40 Right hand Key Blank.