Libre
Soutien
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S
Tapered half round cross section allows use on convex and concave surfaces. Suitable for deburring work. The edges and surfaces are tapered towards the point. 4in and 6in files are fully pointed, 8in and longer semi-pointed. Double cut.Size 300mm (12in)Cut: half round smooth.Tanged.
This Facom 4 piece plier set comprises the following: Locking multi-grip pliers (181A.25CPE).Diagonal cutters (192.16CPE).Half-round nose pliers (185.20CPE).Combination pliers (187.18CPE).
The Faithfull No.4 Smoothing Plane is designed for smoothing and final finishing. Made with a quality grey cast iron body for strength and stability with precision ground base and sides for flatness and squareness. Machined seatings eliminate movement and blade judder. A lever cap with a brass locking screw secures the blade assembly and enables easy release for sharpening. Wooden handles and guidance knobs maximise user comfort. A solid brass blade adjustment nut completes the appeal of these traditional tools. Cutter Width: 50mm.Overall Length: 250mm.This Faithfull No.4 Smoothing Plane is presented in a hinged, wooden storage box.
Powerful and long-life DC motor with overheating and overload protection. Robust solid metal drill chuck with chucking force safety device. Short design of 180 mm. Perfect for use with stepped drill bit, e.g. for drilling initial holes in sheet metals.17 torque levels – force can be easily metered up to 30 Nm for tough screw connections. 2-speed solid metal gearbox. Bright LED light on housing. 2.5 Ah battery capacity for up to 350 screw connections (5 x 40 mm). FEIN SafetyCell technology. Protects the battery and tool from overload, overheating and total discharge. The battery charge can be read off the battery. Includes belt holder and magnetic bit holder. One charger for all FEIN Li-ion batteries of all voltage classes.
The Einhell Power-X-Change Combi & Impact Driver Twin Pack, contains the following: 1 x 18 Volt TE-CD 18-2 Li-i Power X-Change Combi Drill is a powerful and versatile tool for screwdriving, drilling and hammer drilling jobs. It has a robust, long-lasting 2-speed metal gear box for high torque and torque slip coupling that prevents over tightening of screws. Chuck: 13mm Keyless. No Load Speed: 0-320/0-1350/min. Max Torque: 48Nm 25 Settings. Capacity: Concrete: 15mm. Weight: 1.76kg. 1 x 18 Volt TE-CI 18 LI Power X-Change Impact Driver is fitted with a unique triathlon motor that is powerful and efficient for the highest demands in power-sapping screwdriving jobs. The special impact mechanism eliminates any torsion force on the user’s wrist. Short, lightweight design with ergonomic soft-grip surfaces and a rugged aluminium housing with additional rubber supports for increased protection. Bit Holder: 6.35mm (1/4in). No Load Speed: 0-2,300/min. Impact Rate: 0-3,200/bpm. Max Torque: 140Nm. 1 x 18 Volt Power-X-Change Charger that features a 6-step charging condition display and is ready for wall-fastening. The charger uses an intelligent charging-management-system for long battery life (battery status will be constantly checked and accordant loaded, a deeply discharged battery will be charged in repair mode). Input Power: 240 Volt. Output Voltage:21 Volt. Charging Time: 1.5Ah: 30 min, 3.0Ah: 60 min, 5.2Ah: 130 min. Weight: 0.5kg. Also comes with 2 x 18 Volt 1.5Ah Power X-Change Li-Ion Batteries and 1 x Toolbag.