FOX Comp 8 S14, boots

To have a maximum safety the helmet must fit tightly and be correctly and securely fastened, in order not to be able to be taken off neither by pulling it nor by rotating it around the head. If it is too big, it may slide down over the eyes or turn in a lateral direction due to movement during riding, blocking the right visibility. Safety Shell in three sizes (M, L and XL) hand made. The new material is a mix of carbon and aramidic fabric.
Internal Polystyrene in three sizes (M, L and XL). The special shape and construction in different density increases mechanical resistance in the event of accidental shock.
Shield thermoformed froma flat sheet. Each shield is a one-of-a-kind piece with unequalled optical features and mechanical resistance. Thanks to this process, the face shield is anti scratch and anti fog and there is no need to use additional lenses on the visor.
The D-Ring Retention System has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding. ECE 22-05 Comfort Cheekpads completely removable and washable, in different thicknesses for a complete customization of the product. Internal Shell completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in teh internal part of teh helmet and to let off the hot air through the back part.
Inner (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA.
Removeable Nose Protector Ventilation
The Shell is a polystyrene with channels for inside air flows. In the front part there is a Air Ventilation with on/off system, which gets the internal helmet ventilation. On the chin part there is an adjustable Air Ventilation.
Aerodynamics Spoiler and Back Air Ventilation: produced in polycarbonate , it has been studied and tested in wind tunnel, so that the point of detachment of the aerodynamic flow is shifted as far away as possible from the shell. This results in less turbulence and therefore fewer vibrations on the helmet itself. This helmet comes standard with a clear visor.

The Civil Shirt by Macna is made of denim and provided with a subtle Macna logo. This shirt has a regular fit for a universal fit.

Outer garment
Fibretech 500D, soft & stong fabric Softshell panels Armex : high resistance to abrasion on forearm
Membrane
Waterproof & breathable membrane
Isolation
120 g. removable thermo-alu lining
Protection
Adjustable approved elbow protectors Approved shoulder protectors Pocket for approved back protector
Comfort
Regular fit Fixed mesh lining Anti-flutter system on sleeves Cuff fastening Jacket bottom tightening by elastic cord and stopper High comfort collar Reflective material Zip for connecting with trousers 2 outer pockets 1 back pocket 3 inner pockets Puls Air ventilation system Fitex system waist fastening

Specification :Material : PlasticColour : BlackSize : Details show in the pictureCollar Diameter : 18mmHead Diameter : 10mmTo Fit a 6mm HoleQuantity : Pack of 10Manufacturer Part Number : GJ21-68-885BInterchange Part Number : GJ2168885BReference OE/OEM Number : GJ2168885, GJ21-68-885B-02, GJ21-68-885Other Part Number : FCP-0038Description :-These clips are used to fix interior trim panels, linings and fascias into various vehicles.-The head pushes in and expands to hold the clip securely in place.-These clips can also be used for other makes and fit into a 6mm hole.-They are widely used across a variety of Mazda models and in various locations on the vehicles.Package includes : 10 x Clips

* knee/hip protectors (level 1) * one layer construction: Cordura® Denim fabric | Article: Ixon Mikki Ladies Motorcycle Jeans, grey, Size 2XL for Women | Article: Ixon Mikki Ladies Motorcycle Jeans, grey, Size 2XL for Women, grey, Size 2XL for Women

For motorcyclists. Easy to use solutions for riders who need communication during the journey. Tech Specs
English voice prompt support. Pair two cellphones at the same time. Power on voice prompt. DSP Eliminate enviromental noise. VOX function, michrophone shuts off when you don”t talk. Internal three-way switch intercom support. Intercom distance 1000M. Lightning and micro USB compatible.