Abus E60NP Nickle Pearl 10/45 Half Cylinder

Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S

Interchangeable heads for Pipemasters irons.1 x Antex 22mm Heads Only for Pipemaster V00225

These Faithfull Utility Paint Brushes are made from a mix of natural and synthetic bristles and are suitable for use with all types of paint. The brushes feature a rust-resistant ferrule and a contoured handle for greater user comfort.Set of 5 one each of 19, 25, 38, 50, 60mm (3/4in, 1in, 1.1/2in, 2in, 2.1/2in)

These Forgefix Pozidriv Self-Tapping Screws have countersunk heads and are Zinc Plated for increased resistance to corrosion. They tap their own thread in to a pre-drilled pilot hole in sheet or solid material. They are single threaded to resist pull-out. APPLICATION:Ideal for use in many DIY, ironmongery, engineering, electrical and plumbing applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. Countersunk heads are designed to sink flush with substrates to leave a smooth surface finish.Self Tapping Screw Pozi Countersunk ZP 3/4 x 6 Box 200

Cross section allows use on convex and concave surfaces. Tapered very slightly towards point both in width and thickness. Smooth Cut: Approx 62 teeth per 25mm (Fine).Second Cut: Approx 36 teeth per 25mm (Medium).Bastard Cut: Approx 26 teeth per 25mm (Coarse).Size. 300mm (12in)Cut half round bastard Flat Side: Double CutHalf Round: Double Cut.Tanged

Juego de probador de purga de freno de mano Bomba de vacío Moto de coche Kits de bomba de vacío automática Adaptador de tornillo de purga de freno