Spyke Mack Lady WP Tourenjacke wasserdicht Schwarz 44

strapazierfähiges Rindnappaleder anilin Innenhand aus Känguruleder Schoeller®-Keprotec®-Verstärkungen vorgekrümmte Finger Stretcheinsätze zwischen den Fingern und an den Seiten Sturzpads atmungsaktiv

For Backcountry access addicts looking for a more relaxed fit and snowmobile-specific durability, the INSTINCT surely impresses. Designed specifically for mountain and off-trail riders looking for a modestly insulated, comfortable gear set to take them deep. INSTINCT is a new solution with style. Features
guaranteed to keep you dry® gore-tex® performance shell fabric tafetta liner highly breathable insulated hood exterior (3) and interior (2) pockets key clip in pocket articulated elbows ykk® zippers heavy-duty dual-head/two-way center front zipper bottom hem adjustment vertical rear hood draw cord front hood brim draw cord snow dust skirt adjustable velcro cuffs embroidered logos kill switch d-ring mp3 port relaxed fit glove friendly zipper pullers

Weather type
Summer
Lining
Mesh
Visibility
Side Eye Night Eye
Ventilation
Mesh panels
Protection
backprotector prepared protector shoulder & elbows
Other specs
Coat hanger Jeans loop
* "lighter picture" shows the night eye effect

Feature:1. 100% brand new and high quality.2. Used widely for car fender, bumper, door or other car surface.3. High quality plastic material, durable.4. Application: for Toyota, for Honda, etc.5. Easy to use.Specification:Model number: 994265Product name: ClipsCondition: Brand new and high quanlity!Material: PlasticColor: BlackItem Type: Fastener ClipItem Height: 28 mmItem Width: 17.5mmHole size: 8mmQuantity: 50 pcs /setPackage Included:50 X Car Fastener Clips

The SCOTT 350 kids pant combines tough construction with stretch and vent panels for comfort no matter how intense the race gets. It features leather inner knee areas for added durability as well as ribbed spandex in the knees to accommodate knee braces
Features
Articulated pre-bent fi t in rider attack position Ribbed Spandex upper knee Stamped Leather inner knees for durability Natural lower leg cuff Ultra-light TPR’s Nylon 900-D inner lining on knee leather to eliminate knee brace wear

MR. JUMP, the fiber helmet studied in details for comfort, technology and for sure safety for end user. It has been studied and tested to optimize the outside and inside air flows.
OUTER SHELL in tricarboco material, mix of Kevlar, carbon and fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell sizes: XS-L and XL-2XL
INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M and L). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation.
The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding.
MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471
CHEEK PADS completely removable and washable, with different thickness to get a perfect customization od the helmet.
INTERNAL SHELL completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet and to let off the hot air through the back part.
INNER (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper and back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation.
The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses.
weigth: ca. 1000gr