Libre
Soutien
Cobao Car Air Outlet Phone Holder 360 Degree Rotation for 3 to 6Inch Phones AvigraphFeatures:1. Good appearance bracket install on the airoutlet.2. All metal parts have made rust prevention.3. Can rotate for 360 degree,never block your sight.4. Had pass temperature test, salt spray test and vibration test and more;5. Easy to operate and no tools needed,just use one hand can put on the phone;6. Fully enjoy your car traveling and bring more funny to your outdoor life.7. Suits all 3 to 6inch brand Phones.Specification:Brand: CobaoMaterial: High Quallity Silica GelWeight: 0.3kgStretch length: 50mm-95mmSuits for: 55cm to 90cm all brand phonesColor: Blue,Gray,YellowPackage included:1xAirOutletMount
MR. JUMP, the fiber helmet studied in details for comfort, technology and for sure safety for end user. It has been studied and tested to optimize the outside and inside air flows.
OUTER SHELL in tricarboco material, mix of Kevlar, carbon and fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell sizes: XS-L and XL-2XL
INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M and L). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation.
The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding.
MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471
CHEEK PADS completely removable and washable, with different thickness to get a perfect customization od the helmet.
INTERNAL SHELL completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet and to let off the hot air through the back part.
INNER (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper and back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation.
The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses.
weigth: ca. 1000gr
security
Upper and ankle protection Palm reinforcement Double layer of material
domestic equipments
HIPORA® climate membrane Thinsulate stretch panels elasticated reflective material adjustable velcro closure long cuff
properties
waterproof windproof breathable
Klassische Brille, wahlweise mit braunem oder schwarzem Kunstleder, die Gläser sind klar, gelb, getönt oder verspiegelt. Die Aufhängung des Brillenbandes ist mit einem Gelenk versehen, dadurch wird die Brille nicht auseinandergezogen und liegt gut an wenn das Brillenband außen um die Helmschale läuft, auch bei breiten Helmen. Splitterfreie Gläser, CE certifiziert mit UV Blocker, hochwertiges Kunstleder.
Description:1. 100% Waterproof. Never Fade, Never Rust.2. Provide eye-catching show off and personalize your car.3. Helps for protect the Fog Light switch button from scratch or crash.4. Easy installation with double side Automotive tape at the back of covers.Feature:Product Name: Fog Light Button TrimCondition: NewMaterial: Stainless SteelColor: ChromeDimension: 17.5x3cmQuantity: 1pcFitment:For Peugeot 3008 2017-ONFor Peugeot 5008 2017-ONPackage Included:1 X Fog Light Button Trim
Feature:Easily grabbed for changing gears and improves the style of your vehicle.Direct replacement of the original knob, no modification needed so long as thread size matches.Instruction manual is not included.Installation:Step1: Remove the original factory gear knob from shifter.Step2: Place the new knob over the shifter and fasten the correct nut.Step3: Make sure the knob is firmly attached.Specification:Material: Laser cut acrylic plasticColor: Red+white/ blue+purpleLength: 15cmAdapter size: M8x23mm M10x23mmFitment: Universal fit for most vehiclesPackage Included:1 X Shift Knob2 X Threaded Adapter
