Pair 9003/H4 80W 8000LM 6000K LED Xenon White Light Bulbs Headlight Hi-low BeamSpecification:Bulb Size(approx.): 85mm/3.34(H) x 47.2mm/1.86(W)Lamp bead size: 5mmx5mmMaterial: Plastic,AluminumHouse Color: BlackLight Color: Xenon WhiteColor temperature: 6000kBulb Model: 9003/H4Operating Voltage:10V-30VLED Chip Qty: 4 per bulbWaterproof rate: IP67High Beam:Lumens:8000LM/Set (4000LM/Bulb)Power:80W(40W/Bulb)Color temperature:6000kLow Beam:Lumens:4000LM/Set (2000LM/Bulb)Power:40W (20W/Bulb)Color temperature:4000kFeature:1. Beam Angle 360 degrees2. It is durable and convenient.3. Aluminum housing, perfect heat dissipation design.4. Integrated design and waterproof.5. Long LED service life,up to 10,000 hours .6. Plug and play, no modification required.7. Brighter than the regular halogen bulbs and HID Headlights.Note:1. We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need.2. Please allow 0.5-1 inch difference due to manual measurement.(1 inch=2.54cm)3. The color of the actual items may slightly different from the listing images due to different computer screen, thanks for your understanding.4. No Instructions Included.Professional Installation Is Highly Recommended!Package included:2 X Light Bulbs
MR. JUMP, the fiber helmet studied in details for comfort, technology and for sure safety for end user. It has been studied and tested to optimize the outside and inside air flows. OUTER SHELL in tricarboco material, mix of Kevlar, carbon and fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell sizes: XS-L and XL-2XL INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M and L). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation. The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding. MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471 CHEEK PADS completely removable and washable, with different thickness to get a perfect customization od the helmet. INTERNAL SHELL completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet and to let off the hot air through the back part. INNER (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER: Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper and back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation. The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses. weigth: ca. 1000gr
Start your day with this extraordinary design from the Queen Kerosin collection. Features in the western look Embroideries on fit Bicolor Piping collar button tape Bags Fit: slim fit
