Shawl Collar Zip Up Longline Coat

Features:Fits models : CH13, CH14, CH15, CV13, CV14, CV15CV16.Specification:Name: CarburetorMaterial: MetalColor: SilverCarburetor Dimensions:Engine Opening O.D.:27.5mmBolt Hole Spacing:52mmNote:1.Please allow 1-3mm errors due to manual measurement.Package Included:1 X Carburetor

Features
Former JUMP Glove Silicone printing on palms and finger tips for improved grip and braking control Long lasting and flexible material for the perfect fit Lightweight design with bold, non-fade graphics Seamless rollover fingertips Synthetic leather palm, with double layer thumb reinforcement Adjustable Velcro? wrist closure for secure and adjustable fit Pre-curved tailoring for the best fit possible, and helps to eliminate arm pump

Description:High thermal efficiency and rapid temperature rises in 5 seconds.PTC ceramics heats at a constant temperature.Double air vents, single air outlet temperature can be up to 80~100 C.Small size and easy to install.Low energy consumption.Turbo silent fan, low noise.Suitable for tricycles, trucks, cars, van s, tower cranes, forklifts, loaders and other models.Feature:Name: 12V Car HeaterColor: BlackSize: 161225cm (6.34.79.8 inch)Material: Metal shellInner core: Pure aluminum coreHeating method: built-in ceramic PTC heatingHeating rate: 5sAir outlet: 2Voltage: 12VScope of application: Car heating or defrostingPackage Included:1 X Heater1 X Plug Wiring2 X Air Pipe4 X Hose Clamp

MR. JUMP, the fiber helmet studied in details for comfort, technology and for sure safety for end user. It has been studied and tested to optimize the outside and inside air flows.
OUTER SHELL in tricarboco material, mix of Kevlar, carbon and fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell sizes: XS-L and XL-2XL
INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M and L). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation.
The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding.
MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471
CHEEK PADS completely removable and washable, with different thickness to get a perfect customization od the helmet.
INTERNAL SHELL completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet and to let off the hot air through the back part.
INNER (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper and back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation.
The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses.
weigth: ca. 1000gr

Description:1.Fully submersible and perfectly sealed, waterproof spotlight adds a dazzle of color to your pond or fountain2.Comes with LED bulb, 180 degree direction3.Can be mounted vertically or horizontally, adjustable stand lets you point the light at different angles4.Ideal for boat5.Super bright and long-lasting. Easy to installSpecification:Output Power10WInput VoltageDC 12VLifespan50000 HoursMaterialAluminumWaterproof RateIP68Shell ColorBlackPackage Included:2 XIP68 Waterproof Underwater LED light

Outer shell
Chamude synthetic leaher palm (65% polyamide, 35% polyurethane) spandex & mesh fabric (95% polyamide, 5% elastane) back colourfast & sweat-proof Lining
unlined palm Upperhand lined in COOLMAX® and DuPont Fit/features
velcro adjustment at cuffs air-vents on fingers visor wipe silicone-printed palms Protection
hard plastic knuckle protection ball of thumb underlaid with shock-absorbing gel