The Nost rear fender, is a universal fender, which can be modifid to work on all dirt bikes. material polypropylene 7.25 inches/ 184.15mm wide at ther mounting point
Specification:Color: ChromeMaterial: ABS PlasticPlacement on Vehicle:Left, Right, Front, Rear (ONLY FIT LEFT DRIVER CAR)Quantity:8 pcs/set (4 long pieces + 3 short pieces with no keyhole + 1 short piece with keyhole)Fitment: (ONLY FIT LEFT DRIVER CAR)For Mazda 2 (DJ/DL) 2015-2017For Mazda 3 (BM/BN) 2014-2017For Mazda 6 (GJ/GL) 2013-2017For Mazda CX-3 (DK) 2016-2017For Mazda CX-5 (KE/KF) 2013-2018Features:-No cutting or drilling required.-Weather-resistant with long lasting.-A perfect aftermarket replacement.-Easy Peel-N-Stick installation.Adhesive tape included.-Easy remove without any residual, never harm the painting of your car.-Made of high quality ABS with chrome color surface finish,which can upgrade your cars personality.Package Included:1 X 8 pcs/set
3in1 touring jacket with large ventilation possibilities Features 450 D Polyester Air Draft Technology: mesh panels hidden below breast pocket for good ventilation AirVent ventilation zips 3M⢠Scotchlite⢠reflectors detachable Humax® membrane: 100 % waterpoof, 100 % windproof, breathable detachable thermo lining YF protectors on shoulder and elbow certified according to EN 1621-1:2012 elbow protectors are adjustable in height upgradable with back protector SAS-TEC SC-1/12 for sizes XS - L upgradable with back protector SAS-TEC SC-1/13 for sizes XL - 5XL 4 outer pockets, 3 inner pockets safety seams
Urban Outdoor glove made of twisted polyester fabric, internal insulating layer in Thinsulate and ilining in microfleece. Closure with wrist strap. Touch screen on index. – heating system with 4-level adjustment button -Power system Dual Power allows you to use gloves with different types of power supply: Direct connection to a 12 volt source (motorcycle battery) – Connection to two 12-volt Li-PO batteries to be inserted into the glove cuffs- Connection to two 7.4-volt Li-PO batteries to be inserted into gloves cuffs for those activities that do not require a high heating intensity. inside Hypora membrane to make them completely waterproof. Features Connection type Battery, Cable, Dual Power Material Hypora membrane, Polyester, Thinsulate, Touch screen index Technical information 12 V - 37.0 W -3.2 AH 7.4 V - 15.0 W - 2.0 AH Duration 12V Level 1 (White) - 5:00 hours Level 2 (Blue) - 3:30 hours Level 3 (Purple) - 2:30 hours Level 4 (Red) - 2:00 hours Duration 7.4V Level 1 (White) - 6:00 hours Level 2 (Blue) - 4:30 hours Level 3 (Purple) - 3:30 hours Level 4 (Red) - 2:30 hours Please remember, power supplies are not included!
The Carlsbad was built for the hard-charging Adventure rider. Like the Carlsbad Caverns in New Mexico,it has been stripped of everything but it’s essential elements. Light and fast with maximum utility and mobility wrapped into an abrasion resistant,water proof package. Features Gore-Tex® performance shell Guaranteed to keep you dry® 500d cordura® rip stop fabric in abrasion zones Ykk® zippers Leather inner knees with dwr treatment, overlaid on inner leg panels for wear/heat resistance safety D3o® level 1 hip armor(2) D3o® level 1 knee armor(2) cargo 2 storage pockets on side thigh visibility Black3m™ Scotchlite™ reflective material ventilation Front thigh intake vents Back thigh exhaust ventsfit/style/comfort Mapped mesh wicking liner with cordura in inner knee and cuff for wear resistance Adjustable cuff design allows pant to be open enough to adjust boot and knee guards/braces Adjustable waistband via velcro side waist adjusters Articulated fit Glove-friendly zipper pulls
To have a maximum safety the helmet must fit tightly and be correctly and securely fastened, in order not to be able to be taken off neither by pulling it nor by rotating it around the head. If it is too big, it may slide down over the eyes or turn in a lateral direction due to movement during riding, blocking the right visibility. Safety Shell in three sizes (M, L and XL) hand made. The new material is a mix of carbon and aramidic fabric. Internal Polystyrene in three sizes (M, L and XL). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Shield thermoformed froma flat sheet. Each shield is a one-of-a-kind piece with unequalled optical features and mechanical resistance. Thanks to this process, the face shield is anti scratch and anti fog and there is no need to use additional lenses on the visor. The D-Ring Retention System has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding. ECE 22-05 Comfort Cheekpads completely removable and washable, in different thicknesses for a complete customization of the product. Internal Shell completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in teh internal part of teh helmet and to let off the hot air through the back part. Inner (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER: Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. Removeable Nose Protector Ventilation The Shell is a polystyrene with channels for inside air flows. In the front part there is a Air Ventilation with on/off system, which gets the internal helmet ventilation. On the chin part there is an adjustable Air Ventilation. Aerodynamics Spoiler and Back Air Ventilation: produced in polycarbonate , it has been studied and tested in wind tunnel, so that the point of detachment of the aerodynamic flow is shifted as far away as possible from the shell. This results in less turbulence and therefore fewer vibrations on the helmet itself. This helmet comes standard with a clear visor.
