IRWIN Record 200-45 Pipe Cutter is perfect for cutting plastic pipe with exceptionally thin cutting wheel and roller.It will also cut copper tube but its use should be confined to one or the other as cutting copper will reduce the effectiveness of the wheel on plastics. Die-cast body with stove enamelled rust resistant finish. Capacity: 15 to 45mm (9/16 to 1 3/4 in).
Weller Butane Gas operated soldering iron set is suitable for all kinds of applications. The 3 function soldering iron allows the tool to be used for soldering, hot air and open flame with an operating time of 30 minutes. Features Piezo electronic automatic ignition system and gas capacity display. Supplied in a sturdy storage box.Gas not supplied. Use gas refill PGR1. Comes with: Solder, lead free 1.0mm Dia, 15g, Cleaning Sponge, 3 Soldering Tips: Conical 1.0 mm UND, 2.4mm Chisel Shaped, 2.4mm Plus 'Hot Knife' heat shrinking tip. Specification Max. Temperature Soldering Tip: up to 450°C.Hot Air Nozzle: up to 450°C.Open Flame: up to 1300°C.
The Ridgid Micro LM-100 Laser Distance Measure provides simple, quick and accurate distance readings with its ultra-sharp Class II lasers. Distance reading will appear on the easy to read LCD display. The measure enables professional tradesman to quickly determine run distances for bidding, calculate the distance of piping runs, measure trouble spots down the line and quickly determine spacing for code compliance. Measures feet, inches and metres. Stores up to 20 measurements. Bright Backlit Display allows use in poorly lit areas. Rugged over-moulding allows excellent grip. Measurement calculations: area, volume, and indirect measurement calculations. Specification Accuracy: ±1.5mm.Operating Range: 50m.Power Supply: 2 x AAA Batteries (Included).Protection Class: IP 54 (dust & water splash).
These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency. The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved. Ideal for wire harness work, and standard printed circuit board assembly. Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.Length (A): 125mm (5 in). Blade length (B): 16mm (0.63 in). Head width (C): 16mm (0.63 in). Head depth (D): 8mm (0.31 in). Tip width: (F): 1.6mm (0.06 in). Cutting capacity: 0.4-2.0mm. Cutting edge: Micro-bevel. The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are ‘pinched’, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.
Monument Clean & Polish Pads are suitable for cleaning, polishing, rust removal, scrubbing and blending. They are rust proof, washable and will not break up during use. Size: 50 x 250 mm pads, medium grit.
Monument Tap Reseating Tool 1/2 inch re-cuts the seats of worn taps or stopcocks without disconnection from the pipework.Tapered cones screw into the top of the tap body, provided the tap body is threaded to the top. For taps with recessed threads in the body, use the parallel bush series. Cutters are case hardened. The feedscrew allows fine adjustment to the cutter. All parts are interchangeable. Fits old series 1/2 in BS1010 flat seats. Complete with 17 and 19mm (11/16 in and 3/4 in ) flat cutters and a tapered cone.
Faithfull heavy-duty clamps manufactured from a high quality carbon steel bar with large malleable iron clamping heads. Clamp bars have a Black Oxide coating with powder coated heads for complete rust protection. Other features include a high grade steel mainscrew with a wear resistant Acme thread, which applies pressure quickly and smoothly. Tail slides are easily adjusted and secured by a steel pin passing through one of the locating holes. Tail slide and heads are flat bottomed so that the clamp can stand upright without support.
