Acerbis X-Factory Ersatzhandprotektoren Schwarz Weiss Einheitsgröße

Features
Former JUMP Glove Silicone printing on palms and finger tips for improved grip and braking control Long lasting and flexible material for the perfect fit Lightweight design with bold, non-fade graphics Seamless rollover fingertips Synthetic leather palm, with double layer thumb reinforcement Adjustable Velcro? wrist closure for secure and adjustable fit Pre-curved tailoring for the best fit possible, and helps to eliminate arm pump

To have a maximum safety the helmet must fit tightly and be correctly and securely fastened, in order not to be able to be taken off neither by pulling it nor by rotating it around the head. If it is too big, it may slide down over the eyes or turn in a lateral direction due to movement during riding, blocking the right visibility. Safety Shell in three sizes (M, L and XL) hand made. The new material is a mix of carbon and aramidic fabric.
Internal Polystyrene in three sizes (M, L and XL). The special shape and construction in different density increases mechanical resistance in the event of accidental shock.
Shield thermoformed froma flat sheet. Each shield is a one-of-a-kind piece with unequalled optical features and mechanical resistance. Thanks to this process, the face shield is anti scratch and anti fog and there is no need to use additional lenses on the visor.
The D-Ring Retention System has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding. ECE 22-05 Comfort Cheekpads completely removable and washable, in different thicknesses for a complete customization of the product. Internal Shell completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in teh internal part of teh helmet and to let off the hot air through the back part.
Inner (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA.
Removeable Nose Protector Ventilation
The Shell is a polystyrene with channels for inside air flows. In the front part there is a Air Ventilation with on/off system, which gets the internal helmet ventilation. On the chin part there is an adjustable Air Ventilation.
Aerodynamics Spoiler and Back Air Ventilation: produced in polycarbonate , it has been studied and tested in wind tunnel, so that the point of detachment of the aerodynamic flow is shifted as far away as possible from the shell. This results in less turbulence and therefore fewer vibrations on the helmet itself. This helmet comes standard with a clear visor.

Description:1. The back of the light bar affixed with adhesive, easy to install.2. Vibration proof , Waterproof, you can drive safely even on rainy days.3. Flexible,Can be used as front and rear signals.Specification:Product Name: Motorcycle Strip Turn Signal LightMaterial: FPCLight Color: AmberShell Color: BlackInput Voltage: 12VSize: 10.8*1cmLED Type: SMD 5050 LEDCable Length: 48cmWorking Temperature: -20-60 ℃Waterproof Rating: I65Number Of LEDs: 6 Per StripInstallation Method: PasteFitment: UniversalNote:1.We provide clear pictures, measurements where possible.Please check as much as possible to make sure the item is the one that you need.2. Please allow 0.5-1 inch difference due to manual measurement.(1inch=2.54cm)3.There are no instructions included in this kit.If you want to know how to use orinstall it,please contact us by Email.We will provide help as much as possible.Package Included:2 X Turn Signal Lights

Rib and PU-Leather Splicing Stand Collar Single-Breasted Woolen Coat

A classic, belted enduro jacket that recalls the iconic era of motorcycling, the OSCAR by Alpinestars Enduro Jacket fuses heritage style with modern materials. Classic detailing, such as the tilted map pocket and custom OSCAR snap buttons make the Enduro Jacket a standout product. The Enduro Jacket’s design fully embodies 1970s off-road heritage and is a perfect addition to OSCAR by Alpinestars collection.
Features
Heavy waxed cotton main shell is water-repellent and durable, all seams are triple stitched. Removable certified shoulder and elbow protectors is removable, allowing jacket to be worn in a variety of outdoor situations. Back pad compartment with PE padding (Alpinestars Nucleon back protector available as accessory upgrade). External cargo-style pockets with tilted map pocket, plus internal document pocket. Waterproof membrane incorporated between outer shell and flannel liner for excellent levels of weather resistance. Detachable (60g) quilted thermal liner means jacket can be worn in various conditions. A storm-fly front and high collar plus a corduroy collar lining and cuffs for additional levels of comfort. Traditional style belted waist ensure perfect and personalize fitting of jacket. OSCAR by Alpinestars collar and sleeve cuff snaps adjustments.

Aluminium German Germany Flag Badge Grille Emblem Decal Universal DecorationFeature:1. 100% brand new and good quality German Flag Emblem.2. Made with high quality of Aluminum material.3. Adhesive on back, suitable to fix it in front grille steadily.4. Universal fits for most car, such as Volkswagen, Audi, etc..Specification:MaterialAluminium DimensionApprox 63mm*32mmColorYellow+Red+Black PatternGerman FlagInstall PositionFront GrilleQuantity1 pcsWeight9gNote:Please clean the target place by detergent before stick it on.Package Included:1 x German Flag Badge Sticker