5m Neon Strip Lights 360 LEDs 2835 SMD 6mm 1pc Warm White White Red Thanksgiving Day Christmas Waterproof Cuttable Decorative 12 V Lightinthebox

Senco DuraSpin® Collated Chipboard screws. Phillips No.2 drive, Clear Zinc finish, coarse thread. 50 screws per strip. CE-marked (EN14592). Suitable for both cordless and mains operated machines.Senco DuraSpin® Collated Chipboard Screws. Size: 4.0 x 40mm.

The Bosch S922EHM Blades are part of the "Endurance for Stainless Steel" range.  - Carbide Technology & Teeth Ground - For Inox / Stainless Sheets (2-4mm), Inox / Stainless Profiles (up to 100mm diameter) & Glass Reinforced Plastic / Epoxy (up to 100mm) Specification: Total Length : 150mm Tooth Spacing : 1.4mm / 18TPI

Paslode IM350+ Diamond point clipped head Nail packs with paper strip, supplied with Paslode Special Impulse gas fuel cells.FINISH: All Paslode nails are Chrome 6, cadmium and lead free and are available in five finishes to meet corrosion requirements.Bright: Economy and bright nails meet the Eurocode 5 requirements for applications in service class 1 (indoor) Specification - No coating.Galv Plus : Meet the Eurocode 5 requirements for applications in service class 1 and 2 (indoor and covered outdoor) Specification - Zn / Al alloy approx 15µm.Electro Galv : Meet the Eurocode 5 requirements for all applications in service class 1 and 2 (indoor and covered outdoor) Specification - Zn and chromate minimum 7µm.Hot Dipped Galv : Meet the Eurocode 5 requirements for all applications in service class 1, 2 and 3 (indoor, covered outdoor and outdoor) Specification - Zinc coating minimum 50µm Stainless Steel : Meet the Eurocode 5 requirements for all applications in service class 1, 2 and 3 (indoor, covered outdoor and outdoor) Specification - A2 according to AISI 304, and A4 according to AISI 316.SHANK: Smooth Shank: The standard nail, offering high shear value and lowest withdrawal resistance. Fixing across the grain. Fixing into end grain. Clenching applications. Specification - Number of centres will vary with shank diameter.Unilock Shank : Increases withdrawal resistance. Drives easier than ring shank fixing across the grain. Specification - The ringed parts have 24 rings per inch.Ring Shank : Provides the highest withdrawal resistance. Fixing across the grain. Specification - RPI (Rings Per Inch) vary from 16 to 32 depending on Specification.HEAD TYPES :Round Head : The head area is designed to maximise resistance to the head being pulled through Specification - Head size between 2.0 and 2.5 times wire diameter according to EC5Clipped Head : Increases number of nails per strip. The head area is designed to maximise resistance to the head being pulled through Specification - Head area corresponding to full round head area, according to EC5

These Forgefix Set Screws are made from grade 8.8 steel and are zinc plated for increased resistance to corrosion. They are fully threaded and conform to DIN 933 standards.Can be used with many Nut types and washers. APPLICATION:For fastening together numerous types of material or to be fastened in to pre-tapped holes.Widely used in many engineering applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers.High Tensile Set Screw Zinc Plated M10 x 30 Bag 10

The ABUS 41 Series laminated steel padlocks are made up from individually plated laminated steel sections with the bottom most plate hardened. The laminates individually refined with the new 'Etrena' treatment process for optimum protection from corrosion offering up to 40 years weather protection. The rivets in the outer laminates are compressed to protect against the rivet heads being knocked off. Precision pin tumbler cylinder protected against drilling and leverage. Where to use it: Medium security requirementThe cylinder can be re-keyed to match an existing key (Keyed Alike). Overall width: 44 mmOverall height: 60 mmOverall depth: 26 mm Shackle width: 18.5 mm I.D.Shackle height: 20 mmShackle Dia: 7 mm

Forge aluminium value door handles. Sprung lever on backplate. Fixings included. Fitting Instructions:1. Place the spindle bar through an existing tubular latch or lock and position one handle over the spindle bar. Ensuring the handle is square, mark the screw hole positions with a Bradawl.2. Drill Ø2mm Pilot holes and reposition the handle before securing using the wood screws provided.Designed to be used with a Euro cylinder mortice lock with centres of 57mm.