Libre
Soutien
Corona R4DM-SB 2.4G 4CH DMSS Compatible Receiver With S.BusDescription:The Corona R4DM-SB is a 2.4GHz DMSS compatible receiver that is designed to use with JR DMSS 2.4GHz transmitters, such as XG6,XG7,XG8 ,XG11 and XG14 under DMSS protocol mode.Specification:Brand Name: CoronaItem Name: R4DM-SBChannels: 4Modulation: DMSSBand: 2.4GHzWeight: 7gVoltage Range: 3.6 ~ 8.5VOperating Current: 60mA max, 35mA under loadOperating Temperature: -10~70 degrees CLatency: 13 ~ 14msSensitivity: -96dBmFeatures:Full range receiver4 Channels - throttle, aileron, rudder, elevatorSupports S.BUS connectivityFor use with JR DMSS transmittersLightweight and compact weighing in at just 7 gramsFail safe programmableBind Procedure:Turn on the DMSS transmitter, leave it 0.5M~1M away the receiver.Connect a shorter on CH2 of R4DM(signal and GND) when bind with XG7; and connect a shorter on CH3 of R4DM when bind with other transmitters.Connect the battery to the receiver(CH1 or CH4 of R4DM) while pressing down receivers button.Red LED light on and Green LED off when searching signals, and turn to Green LED light on and Red LED off indicate bind is succeeded.Fail-safe Setting:R4DM set failsafe on the DMSS transmitter just like the operation of the JRs DMSS receivers. We highly recommend you set failsafe feature while flying your models. An example of a useful Failsafe setting would be to shut down the models throttle, so that it does not fly or drive away uncontrolled.Special/Normal Mode Switch Guide: If you
Holybro Kakute F4 V2 STM32F405 Flight Controller With Betaflight OSD for RC Multirotor FPV Racing DroneDescription: The Holybro Kakute F4 flight controller supports important features of Betaflight/Cleanflight, such as OSD and Dshot. The fasterF4 processor gives room for future feature development: run all features at the fast 8 kHz PID loop rate, at single-digit CPU utilization!Because of issues with serial inversion, other F4 boards struggle to support protocols such as FrSky SBUS and SmartPort at the sametime. The Kakute F4 is designed to support all serial protocols at once.Specification (user manual):MCU: STM32F405RGT6 32-bit processorIMU: ICM20689 (SPI)Barometer: BMP280USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)5 hardware UARTS (UART1,3,4, 5, 6)Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.128 Mbit Dataflash chip for Blackbox loggingDimensions: 35x30x8mm (includes USB in height)Mounting Holes: Standard 30.5mm square to center of holesWeight: 7gNew V2 Features:-Additional UART (UART 4) added to support serial camera communication such as to RunCam Split. Please note this is NOTthe same as Betaflight Camera Control feature, which controls the menu of FPV cameras like Swift, etc.-Additional UART (UART 5) added to support ESC telemetry such as from BLHeli_32 and KISS.-Through-hole solder pads instead of flat pads for more secure soldering especially for beginners.-Barometer sensor
Squishy Squeeze Toy Simulate Soft Vegetable Fruit Banana Carrot Phone Bag Straps Stress Reliever
Flytec 2011-5 Fisch Finder 1.5kg Laden 500m Fernbedienung Fischköder Boot RC Boot
LEGO Friends 41315 Heartlake Surfladen (41315)