Dainese Street Darker Motorrad Lederjacke Braun 50

Protection
certified under norm EN 13594:2015 "protected glove for motorcyclists" hard plastic knuckle protection knuckle protection tested (impact test for knuckle protection) special foam knuckle & finger protection reinforced edge of hand reinforced edge of hand & thumb
Fit/features
stretch fabric panels on back perforated finger side walls special flat seam velcro adjustment at cuffs
Lining
unlined palm lightweight lined back
Outer shell
deer leather palm supple cowhide back colourfast & sweat-proof

MR. JUMP, the fiber helmet studied in details for comfort, technology and for sure safety for end user. It has been studied and tested to optimize the outside and inside air flows.
OUTER SHELL in tricarboco material, mix of Kevlar, carbon and fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell sizes: XS-L and XL-2XL
INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M and L). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation.
The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding.
MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471
CHEEK PADS completely removable and washable, with different thickness to get a perfect customization od the helmet.
INTERNAL SHELL completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet and to let off the hot air through the back part.
INNER (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper and back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation.
The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses.
weigth: ca. 1000gr

nullSpecifications:Product name: License Plate Framecolor: black, gray, red, blueSize: 310 * 160mmFeatures:1. Using environmentally friendly food grade silicone material, non-toxic and tasteless.2. The material performance is stable, it does not deform at high temperature 240 °, and does not age at low temperature minus -40 ° C.3. No rust, no shaving, no hardness, no damage to car paint, no license plate, no noise!4. The package frame is perfectly designed, without blocking any content of the license plate.5. Strong resiliences and flexibility, resistant to bending and stretching, skin-friendly feel is very good.6. Easy installation and stable, durable.Package Included:2 * License plate holderSome accessories

Born from the previous women s glove, Spidi Grip 2 takes all the salient features and elevates them to new standards. Designed on female morphology, as all Fit For Lady products, features silicone inserts on the fingertips to improve grip on the tank of the bike. Features
Cowhide leather 0.7 mm thickness Clarino Palm Inserts in stretch fabric Knuckle protection in shock absorbing material Adjustable Velcro Closure

Acerbis X-Factory Ersatzhandprotektoren15 Farben Einheitsgröße Anwendung: auf Lenkern mit Innendurchmesser von 13,5 mm bis 16 mm und Außendurchmesser von 22 mm bis 28 mm

Deep inside a desert burial mound you find him, the all-powerful god of mountain and earth. It is in front of him that you will answer the riddle of steel and the calculus of cool. For he is Krom, and you will not be cast out of Valhalla. Not you, not today. Features
Meets DOT FMVSS 218 (US), ECE 22-05 (Europe), & PSC (Japan) Helmet Safety Standards. Does not ship with PSC certification stickers unless purchased from an authorized dealer in that country. Includes internal DropShield™ and Clear quick-change fog-free FliteShield™. Removable HydraDry™ moisture wicking liner. Injection molded Polycarbonate shell for strength.
Fit The most common helmet fit type, the Intermediate Oval head is slightly shorter front-to-back and a little wider side-to-side. Venting 4 intake vents, including a MX inspired chinbar vent, and 2 exhaust ports are coupled with deep channeling in the interior energy absorbing EPS foam resulting in superior helmet venting. Weight Average - A reduced shell profile helps reduce overall weight, while maintaining the the exclusive World Standard of ICON to suit your riding style. Exterior The helmet’s ventilation system consists of strategically placed air vents, intakes, air channels and exhaust ports. The oversized chinbar intake enhances airflow, keeping you cool by routing air where you need it most. A decrease of both drag and weight was achieved by sculpting the traditional neckline of the Airflite to avoid jacket or suit interference. Shield The Airflite has not one, but two shields. The unique quick-change fog-free shield keeps debris away from your money maker, while the internal interchangeable drop shield has the sun in check. No more swapping shields for cloudy or sunny days. Just reach up, flip the switch, and ride forever. Interior The removable sweat wicking Hydradry™ liner provides a snug and contoured fit. Air from the vents is channeled between the comfort liner and the protective,energy absorbing EPS foam liner to create a nearly perfect rider-focused interior. The airflow works in conjunction with the Hydradry™ liner to effectively reduce heat build up. Combine that with superior venting and a removable breath deflector which creates a nearly perfect rider-focused enclosure. ICON FliteShield™ Compatible with the Airflite™ helmet. Featuring a 3D molded process for optical clarity, and a fog-free coating. Icon DropShield™ Instead of carrying an extra FliteShield™ for changing light conditions, with the flip of a switch, engage the tinted DropShield™ hidden within the helmet.