The Olympia 6 piece set of 12mm bungee cords. Avaliable in 3 lengths: OLY05432: 60cm.OLY05433: 90cm.OLY05434: 120cm. Working Capacity: 12kg.Break Strength: 48kg.The Olympia Bungee Cords have the following specification: Length: 120cm.Width: 12mm.Colour: Yellow.Quantity: 6 Piece.Working Capacity: 12kg.Break Strength: 48kg.
The Einhell Power-X-Change Combi & Impact Driver Twin Pack, contains the following: 1 x 18 Volt TE-CD 18-2 Li-i Power X-Change Combi Drill is a powerful and versatile tool for screwdriving, drilling and hammer drilling jobs. It has a robust, long-lasting 2-speed metal gear box for high torque and torque slip coupling that prevents over tightening of screws. Chuck: 13mm Keyless. No Load Speed: 0-320/0-1350/min. Max Torque: 48Nm 25 Settings. Capacity: Concrete: 15mm. Weight: 1.76kg. 1 x 18 Volt TE-CI 18 LI Power X-Change Impact Driver is fitted with a unique triathlon motor that is powerful and efficient for the highest demands in power-sapping screwdriving jobs. The special impact mechanism eliminates any torsion force on the user’s wrist. Short, lightweight design with ergonomic soft-grip surfaces and a rugged aluminium housing with additional rubber supports for increased protection. Bit Holder: 6.35mm (1/4in). No Load Speed: 0-2,300/min. Impact Rate: 0-3,200/bpm. Max Torque: 140Nm. 1 x 18 Volt Power-X-Change Charger that features a 6-step charging condition display and is ready for wall-fastening. The charger uses an intelligent charging-management-system for long battery life (battery status will be constantly checked and accordant loaded, a deeply discharged battery will be charged in repair mode). Input Power: 240 Volt. Output Voltage:21 Volt. Charging Time: 1.5Ah: 30 min, 3.0Ah: 60 min, 5.2Ah: 130 min. Weight: 0.5kg. Also comes with 2 x 18 Volt 1.5Ah Power X-Change Li-Ion Batteries and 1 x Toolbag.
DEWALT Mesh Sanding Discs last at least 4 times longer than traditional DEWALT sandpaper discs. Fibres are drawn away from the surface of the sanding disc into the small holes, and don't sit between the material and abrasive. This optimises the sanding effect. These sanding discs enable dust to be drawn through the mesh across a wider area rather than being limited to distinct holes in traditional sanding discs. They are also much easier to select as there is no requirement to match a specific dust extraction hole pattern. The mesh sanding discs have hook and loop fastening for quick and easy attachment. They can be easily cleaned to help prolong their life.The DTM3125 Mesh Sanding Discs have the following specifications:Size: 150mm.Grit: 120.Pack quantity: 5.
The Norbar Adjustable Industrial Torque Wrenches have a robust construction, which gives accurate results to ±4%, even in arduous working conditions. Their large break angle improves accuracy by reducing the possibility of over torqueing and the cam control of the mechanism gives a controlled break which will not throw the operator off balance. The torque wrenches are dual scaled, with both N.m (Newton Meters) and lbf.ft graduations. Supplied with a declaration of conformance to satisfy the requirements of ISO 6789:2017 and carry case for storage and protection. 3AR Industrial Torque Wrench Specification Drive: 3/4in Square.Range: 100 – 500Nm (70 – 350 lbf.ft).Torque Radius: 683.4mm.Ratchet Teeth: 36.Ratchet Type: Push-Through.Length: 910mm.Weight: 5.2kg.
The Blue Spot Fine Thread G Clamps have a fine thread with reinforced shoulders for strength. They have a malleable cast iron frame, a tommy bar handle and swivel shoe.Size: 102mm (4 inch).
