Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S
The Milwaukee® M12 CID Fuel™ 6.35mm (1/4in) hex Impact Driver has 2 modes to cover a number of applications. Mode 1 (0-1,200 rpm, 19Nm torque) is ideal for precision work, whereas Mode 2 (0-2,650rpm, 135Nm torque) delivers maximum performance for the toughest applications. It also has a bright LED light to illuminate the workspace. Designed to out-perform other heavy-duty power tools, it has POWERSTATE™ brushless motors for up to 10 times longer motor life. REDLINK PLUS™ intelligence, providing total system communication with overload protection to increase the tool's life. REDLITHIUM-ION™ battery packs are highly durable and feature a fuel gauge to display the remaining charge. Individual cell monitoring in the battery optimises tool run time. M12 CID-202C: 2 x 12v 2.0Ah Li-Ion Batteries. M12 CID-0: Bare Unit, No Battery or Charger. Specification Bit Holder: 6.35mm (1/4in). No Load Speed: 0-1,200/0-2,650/min. Impact Rate: 2,700/3,550/bpm. Max Torque: 19/135Nm.
The Wera Slotted 160i VDE insulated screwdrivers are tested individually for dielectric strength under a load of 10,000 volts so as to ensure safe working with loads up to 1,000 volts. They have a premium lasertip which is a laser roughened surface that literally bites into the screwhead, reducing cam out. With patented ergonomic, multi component Kraftform handle which uniquely fits to the shape of the hand during screwdriver use. Please note: WER006100 does not have a Lasertip.Blade Length, 150mmTip, 6.5mm
These Faithfull professional, high quality Combination Spanners are forged from chrome vanadium steel, which is hardened, tempered and satin chrome plated for corrosion protection. Manufactured to DIN 3113 standards. The broached jaws and rings ensure a consistent tolerance and a guaranteed accurate fit. Both the jaw and ring end are set at a 15 degree offset for ease of use in awkward positions.Size 22mm
