Abus E60NP Nickle Pearl 10/45 Half Cylinder

Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S

The Squire CombiBolt3 is a unique, recodeable locking bolt with 3 die cast zinc wheels for 1,000 possible combinations. The bolt has a die cast lock body and has high pick resistance. It is simple to use and install and allows one-handed operation. The CombiBolt3 is lockable in the open and closed position for extra security. It is rustproof and suitable for harsh environments. The bolt can be used indoors and outdoors, and is ideal for the following:ShedsCupboardsStorage areasCabinetsLockersVehiclesBeach hutsBoatsInternal DoorsGatesUp and over garage doors. Specifications:Body Width: 37mm.Body Length: 90mm.Bolt: 10mm steel.Finish/Colour: Satin Chrome.

Double ended box spanners are thinner than a socket and are much longer so that they can be used to loosen or tighten bolts and nuts in narrow recesses, meaning that they are often used in plumbing maintenance and automotive repair. This tubular box spanner is made from bright plated steel and able to accommodate a tommy bar.Size 18 x 21mm Length 150mm (6 in)

Pin vices are chiefly used for holding small taps, reamers, scribers or wire. The handles are tubular which permit holding wires of any length or diameter up through the length of the tool.Size: 1Capacity: 0 - 1mm (0 - 3/64 in)

These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency. The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved. Ideal for wire harness work, and standard printed circuit board assembly. Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.Length (A): 125mm (5 in). Blade length (B): 16mm (0.63 in). Head width (C): 16mm (0.63 in). Head depth (D): 8mm (0.31 in). Tip width: (F): 1.6mm (0.06 in). Cutting capacity: 0.4-2.0mm. Cutting edge: Micro-bevel. The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are ‘pinched’, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.

Masajeador muscular eléctrico de 12 V Percusión portátil Vibrante Pistolas de masaje potentes Masajeador muscular de tejido profundo de mano para cuello Espalda Hombros Pie pierna