Eliminación de terminales de engarce Kit de herramientas Reparación de cables Juego de herramientas con pelacables Engarzadores de alambre Destornillador de trinquete Terminal aislado

The DMT D9 Diamond sharpening bench whetstone has non-slip feet and will not break, chip, crack, hollow or groove. The D6 whetstone is made from the hardest material which is one of the most efficient sharpening abrasive. Available in unique interrupted surface and continuous surface, light pressure produces a sharp edge with just a few strokes. Use water for lubrication no oil, smell or mess and can hone ALL hard materials: carbide, steel, etc. and is supplied with Non-skid mat. Precision, continuous monocrystalline diamond bench whetstones with rubber feet. The grit size is etched into the side of the whetstone. The grits are denoted by a dual coloured circle which is set into one end. Blue: Coarse Grade 325, 45 micron.Red: Fine Grade 600, 25 micron.Green: Extra Fine Grade 1200, 9 micron.Red: Fine 600g, 25 micron

The Lindstrom Supreme Oblique Cutting Nipper produced from high performance tool steel. It has a screw joint that minimises friction and alignment of cutting edges. The edges are precision induction hardened to 58-60 HRC. The handles with return spring and sleeved.Length (A): 108mm (4.25 in).Blade length (B): 8mm (0.31 in). Head width (C): 10.5mm (0.41 in). Head depth (G): 15mm (0.59 in). Cutting capacity: 0.35-1.25mm. Head type: Double angled. Cutting edge: Flush. Angled heads, also known as oblique style, are set at an angle to the main body of the cutter. This means that the cutter can reach between parts and areas which are difficult to access. The Flush Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are ‘pinched’, allowing less altitude and a smaller overall surface area – more than Micro-bevel cuts. The cutters have fine cutting edges that leave a narrow and short taper and small exposed area. They can be used to meet tight specifications for a flush result to a board, component or part.

The Britool 3/8 inch 12-point sockets (metric) are crafted from chrome vanadium steel with a high chrome finish. The OGV profile allows tightening torque to be applied to the sides rather than to the angles of the nut. This product is for manual use only. ISO 2725-1, DIN 3124, ISO 1174-1, ISO 691, ISO-1711-1.Size: 11mm Length: 25.7mmWeight: 22g

The Apache ATS Soft Shell Jacket has a lightweight, water resistant design for cooler days. This jacket is breathable and has a micro-fleece inner for added comfort. Two zipped secure side pockets. Soft expandable cuffs to sleeves. The detail to chest is reflective for added safety.

The DEWALT DCK206M2 Twin Pack, contains the following: 1 x 18 Volt DCH253 3 Mode SDS Hammer Drill that is ideal for drilling anchors and fixing holes into concrete, brick and masonry from 4mm to 24mm. The hammer drill has a rotation stop mode for light chiselling in plaster, tiles and render and an impact stop mode for rotary only drilling in wood and metal. It uses 4.0Ah 18 Volt Lithium Ion batteries to deliver high performance, long life and maximum runtime. No Load Speed: 0-1,200/min.Impact Rate: 0-4,500/min with 2.1 Joules.Capacity: Concrete: 24mm, Steel: 13mm, Wood: 26mm.Weight 3.1kg. 1 x 18 Volt DCD785 XR Compact Hammer Drill Driver has an ultra compact, lightweight design that allows it to be used in confined spaces, whilst the intelligent trigger design allows for total control of application. It has a two speed, all metal transmission for increased run time and a longer tool life. Chuck: 13mm Keyless.No Load Speed: 0-600/0-2,000/min.Impact Rate: 0-10,200/0-34,000/bpmTorque: 60Nm, 14 Settings.Capacity: Steel: 13mm, Masonry: 13mm, Wood: 38mm 1 x 10.8-18 Volt DCB105 Multi-Voltage XR Charger varies the charge rate according to battery type to increase battery pack life. It features diagnostics with bright LEDindicator which communicates the battery charge status: charged, charging, power problem, and battery too hot or too cold. Charges all XR Li-Ion DEWALT Slide Pack 10.8, 14.4, and 18 Volt batteries.

Succeeding the HP330 which was developed by adding hammer mechanism to drill driver model DF330D. Coming from solid tried and tested heritage but with slide on Compact eXtreme Technology Batteries. Featuring increased motor power for higher application speed and a max tightening torque. The rubberised handle has been designed for best grip and maximum thrust to the bit. A single LED joblight has pre-glow and after-glow functions handy for working in dark conditions.