Stahlwille Combination Spanner 8 mm

Monument D.I.Y. Tap Reseating Tool re-cuts the seat of leaking taps. Fits BS5412 & BS1010 1/2in and 3/4in taps. Complete with: 17, 19 and 25mm (11/16in 3/4in 1in) Flat Cutters and two double ended plastic bushes. Made in Britain.

Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S

The ultimate tool for maintained razor edges, even on hard stainless blades. For the food service and meat processing industries. Long wearing monocrystalline diamond surface.Solid steel round rod for maximum diamond surface.Large Safety Guard.Colour coded hang ring for identification.High impact resin handle.Green Extra Fine.Size. 300mm (12 in).

These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency. The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved. Ideal for wire harness work, and standard printed circuit board assembly. Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.Length (A): 125mm (5 in). Blade length (B): 16mm (0.63 in). Head width (C): 16mm (0.63 in). Head depth (D): 8mm (0.31 in). Tip width: (F): 1.6mm (0.06 in). Cutting capacity: 0.4-2.0mm. Cutting edge: Micro-bevel. The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are ‘pinched’, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.

The Faithfull sleek heavy-duty aluminium tacker featuring a unique Triggershot action that can be selected when placing staples in hard to reach places and is ideal for single-handed use when flush stapling or when precise positioning is required. Additional features include force adjustment, an easy drop-in loading system with a reload indicator and a built-in handle lock for easy storage. Accepts: Staples No.4: 6-14mm.Brad Nails No.8: 12-14mm.Pin Nails No.9: 14mm.

Dobladora de tubos de alta resistencia de 180 grados Dobladora de tubos de 8 mm Tubo de cobre de 5/16 "Herramienta de doblado de tubos de aire acondicionado Herramienta de codo manual