Premier Vintage Carbon, jet helmet

Features
All World Standard, meets or exceeds the following: DOT FMVSS 218 (US ), ECE 22-05 (EUROPE), SAI AS1698 (AUSTRALIA) & SG (JAPAN) SAFETY AND TESTING STANDARDS. does not ship with sai or sg certification stickers unless purchased from an authorized dealer in that country. Injection molded Polycarbonate Shell for strength and durability Recessed Twin Channel Supervent™ with industry leading intake and exhaust ports for increased cooling. Fog-Free Icon Optics™ shield with Prolock™ shield locking system Adjustable chin and forehead venting system maintains continual temperature for increased comfort in any riding situation. Rapid Release™ Shield Change System Removable molded breath deflector helps prevent fogging Fully removable washable HydraDry™ Moisture Wicking Interior Easy adjust ergo vent switch for superior or air flow control. Available in four shell sizes with an Icon exclusive long oval headform for ultimate fit and comfort.

Features
Nylon lining quilted to 100gram polyester insulation Mock-neck collar Left-chest map pocket Two lower-front pockets Two inside pockets, one with zipper closure and one with hook-and-loop closure Lower pockets have hidden snap closure Drawcord adjustable hem Triple-stitched main seams Drop tail

Germot Varese, textile pants waterproof

MR. JUMP, the fiber helmet studied in details for comfort, technology and for sure safety for end user. It has been studied and tested to optimize the outside and inside air flows.
OUTER SHELL in tricarboco material, mix of Kevlar, carbon and fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell sizes: XS-L and XL-2XL
INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M and L). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation.
The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding.
MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471
CHEEK PADS completely removable and washable, with different thickness to get a perfect customization od the helmet.
INTERNAL SHELL completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet and to let off the hot air through the back part.
INNER (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper and back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation.
The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses.
weigth: ca. 1000gr

Description:Sturdy and durable key ringsGreat for DIY crafts, keys, etcSpecification:Color: SilverMaterial: IronDiameter: Approx. 2.3cm/0.91Chain Length: Approx. 2cm/0.79Note:Keyrings only, other accessories are not included.Package Included:50 X Key Rings

The Forcefield Upgrade back protector inserts are designed to replace existing back protector inserts and comply with the EN1621-2: 2003 Level 1 standard. With Nitrex® a unique high-tech shock-absorbing material, energy can be scattered and absorbed, and evenly distributed over the Nevertheless, the protector is flexible and comfortable. The materials used can withstand repeated impacts. A combination of technology and Multi Nitrex layers allows Forcefield to manufacture more lightweight and flexible protectors. This allows the body to move without being restricted. The unique triangular Nitrex grids have been designed to allow breathing holes at the base for breathability, and this also reduces weight. Features
Approved to: EN1621-2: 2003 Level 1 Protector strength: 15.5 mm