TPU Remote Smart Key Cover Fob Case Shell For Mazda 2 3 4 6 CX-3 CX-5 CX-7 MX5

Features
Single density eps liner features extensive venting that aligns with two large front Air intakes and rear exhausts Injection molded polycarbonate/abs shell Fully adjustable visor provides ample coverage Removable/washable liner Flexible rubber nose piece helps deflect roost Hi- flow mouth vent with filter to prevent roost Rear shell shape easily repositions the goggle strap

Sexy Plunge Hip-lifting Lace Crocheted Bras Set

Seamfree Ice Silk Wireless Longline Sport Vest Yoga Sleeping Breathable Bras

Zipper Ankle Boots For Women

To have a maximum safety the helmet must fit tightly and be correctly and securely fastened, in order not to be able to be taken off neither by pulling it nor by rotating it around the head. If it is too big, it may slide down over the eyes or turn in a lateral direction due to movement during riding, blocking the right visibility. Safety Shell in three sizes (M, L and XL) hand made. The new material is a mix of carbon and aramidic fabric.
Internal Polystyrene in three sizes (M, L and XL). The special shape and construction in different density increases mechanical resistance in the event of accidental shock.
Shield thermoformed froma flat sheet. Each shield is a one-of-a-kind piece with unequalled optical features and mechanical resistance. Thanks to this process, the face shield is anti scratch and anti fog and there is no need to use additional lenses on the visor.
The D-Ring Retention System has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding. ECE 22-05 Comfort Cheekpads completely removable and washable, in different thicknesses for a complete customization of the product. Internal Shell completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in teh internal part of teh helmet and to let off the hot air through the back part.
Inner (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA.
Removeable Nose Protector Ventilation
The Shell is a polystyrene with channels for inside air flows. In the front part there is a Air Ventilation with on/off system, which gets the internal helmet ventilation. On the chin part there is an adjustable Air Ventilation.
Aerodynamics Spoiler and Back Air Ventilation: produced in polycarbonate , it has been studied and tested in wind tunnel, so that the point of detachment of the aerodynamic flow is shifted as far away as possible from the shell. This results in less turbulence and therefore fewer vibrations on the helmet itself. This helmet comes standard with a clear visor.

Speicification:Material: metal +plasticColor:BlackFeatures:1 sets, completeLong service life and durabilityApplication:For Kawasaki EL EN ER GPZ KLE ZL 500 600 GPZ 500 S 1983-87(Details applicable models, please see the table picture)Numbering:WVCB A9 WVA9 AK WVAK CAB-S16, 13370-08F50(08F00) 13258-04F00Package Included:1 X Carburetor Repair Rebuild Kits