Kostenlos
Unterstützung
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S
Tapered half round cross section allows use on convex and concave surfaces. Suitable for deburring work. The edges and surfaces are tapered towards the point. 4in and 6in files are fully pointed, 8in and longer semi-pointed. Double cut.Size 300mm (12in)Cut: half round smooth.Tanged.
Ideal for sensitive workpieces and right angles. The large, perfectly parallel jaw faces are characteristic of the original BESSEY K-body clamp. They allow easy clamping and spreading of sensitive surfaces and right angles. Also round and pointed workpieces. And the best thing is: thanks to their extra-large contact surfaces, the original BESSEY K-body clamp are universally applicable even behind and to the side of the high-quality profiled rail. This allows you to clamp in locations that conventional screw clamps are unable to reach. That's guaranteed! The K-body clamp holds workpieces exactly parallel. Parallel jaw faces with extra-large contact surfaces.Clamping of various shapes, along the whole length of the rail.Universally applicable.Light and easy-to-handle.No need for tools for switching between clamping and spreading. Your benefits at a glance:1 Parallel jaw faces.The large, planar jaw faces made from impact and fracture-resistant reinforced polyamide are exactly parallel. For gentle clamping of a very wide range of different shapes over the entire length of the rail, without spacers. 2 High-quality profiled rail.The BESSEY hollow profile rail from our own drawing plant has been especially optimised for clamps. The profile acts as a reliable reinforcement against torsional forces, while the serration prevents the clamp from slipping. 3 Removable end stop.The end stop made from impact-resistant polyamide also gives the clamp added support. It can be removed without any tools, to allow the lower arm to be quickly turned around and used for spreading.The Bessey UK30 Uniklamp has the following specification: Clamping Force: up to 1,500N.Opening 600mm.Throat Depth: 80mm.Rail: 20 x 5mm.Weight: 0.93kg.
The Arrow RL100 riveter is made of an all steel construction with comfortable vinyl grip. The spring-loaded handle allows for easy rivet loading and ejection, with the changeable nose piece taking a 1/8 diameter rivet in one hole, and 5/32 and 3/16 diameter in the other hole. To change hole size simply loosen screw on nose piece plate, swing pivot plate around then re-tighten screw.Riveter only without any rivets supplied
Máquina multifuncional de sujeción de sujeción de sujeción de llaves para la herramienta de copia de llaves de automóviles de acero inoxidable universal
Magnetic screwdriver bit holder for 1/4in shank screwdriver bits.