Kostenlos
Unterstützung
The Trend VJSAG36 is an adjustable angle guide to allow grooving with the router, or crosscutting with a circular saw. It has an adjustable angle range from 25º to 155º and preset angle for 30º, 45º, 60º, 90º, 120º, 135º and 150º. The router working length at 90º is 915mm (36 inch), the circular saw working length at 90º is 780mm (30 3/4 inch). It has an angle tolerance ± 0.2º with zeroing facility, adjustable position alloy extrusion with scale and requires three clamps. Will accept accessory friction clamps Ref. VJS/CK or VJS/CK/L.
The ALM Manufacturing Replacement Chainsaw Chains to fit a wide range of chainsaw makes and models.The ALMCH066 Chainsaw Chain has a 3/8 inch Low profile (L/P), 0.043in guidebar slot 0.325 mm and Low profile (L/P) 1.1 mm guidebar slot.This chain is made to fit the Ryobi range and suit saws with a 40cm bar and chain with 66 drive links including:PCN-3840, PCN-4040.
Wera Zyklop HMB 3/8in Drive Metric Sockets for hex-head fasteners.Suitable for manual and (non-impact) machine applications. With ball intercept ring and rear end knurling for reliable manual precision. Chrome vanadium, brushed chromium plated.
Paslode IM350+ Diamond point clipped head Nail packs with paper strip, supplied with Paslode Special Impulse gas fuel cells.FINISH: All Paslode nails are Chrome 6, cadmium and lead free and are available in five finishes to meet corrosion requirements.Bright: Economy and bright nails meet the Eurocode 5 requirements for applications in service class 1 (indoor) Specification - No coating.Galv Plus : Meet the Eurocode 5 requirements for applications in service class 1 and 2 (indoor and covered outdoor) Specification - Zn / Al alloy approx 15µm.Electro Galv : Meet the Eurocode 5 requirements for all applications in service class 1 and 2 (indoor and covered outdoor) Specification - Zn and chromate minimum 7µm.Hot Dipped Galv : Meet the Eurocode 5 requirements for all applications in service class 1, 2 and 3 (indoor, covered outdoor and outdoor) Specification - Zinc coating minimum 50µm Stainless Steel : Meet the Eurocode 5 requirements for all applications in service class 1, 2 and 3 (indoor, covered outdoor and outdoor) Specification - A2 according to AISI 304, and A4 according to AISI 316.SHANK: Smooth Shank: The standard nail, offering high shear value and lowest withdrawal resistance. Fixing across the grain. Fixing into end grain. Clenching applications. Specification - Number of centres will vary with shank diameter.Unilock Shank : Increases withdrawal resistance. Drives easier than ring shank fixing across the grain. Specification - The ringed parts have 24 rings per inch.Ring Shank : Provides the highest withdrawal resistance. Fixing across the grain. Specification - RPI (Rings Per Inch) vary from 16 to 32 depending on Specification.HEAD TYPES :Round Head : The head area is designed to maximise resistance to the head being pulled through Specification - Head size between 2.0 and 2.5 times wire diameter according to EC5Clipped Head : Increases number of nails per strip. The head area is designed to maximise resistance to the head being pulled through Specification - Head area corresponding to full round head area, according to EC5
These Forgefix Pozidriv Self-Tapping Screws have countersunk heads and are Zinc Plated for increased resistance to corrosion. They tap their own thread in to a pre-drilled pilot hole in sheet or solid material. They are single threaded to resist pull-out. APPLICATION:Ideal for use in many DIY, ironmongery, engineering, electrical and plumbing applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. Countersunk heads are designed to sink flush with substrates to leave a smooth surface finish.Self Tapping Screw Pozi Countersunk ZP 3/4 x 6 Box 200
The RIDGID Constant Swing Tube Cutter features an enclosed feed screw to eliminate clogging and jamming, grooved rollers for close-to-flare cuts, and a fold-away reamer. It has an X-CEL Knob that cuts tubing more quickly and easily with the larger, more ergonomic design. Whilst the X-CEL Wheel Pin helps to change your cutter wheel quickly using the new ball detent design, no tool needed and no lost clips. It is made from high-strength zinc alloy and there is a spare cutter wheel included in the knob. It cuts copper, brass, and aluminium tubing and thin-wall conduit. RID66742 is fitted with a heavy-duty cutting wheel.RIDGID 66742 Heavy-Duty Constant Swing 150LS Tube Cutter. Std. Wheel: E-4546.Capacity: 6-35mm (1/4 - 1.3/8in).Weight: 0.47kg.