Rustins Quick Dry Radiator Enamel Satin White 250ml

Jubilee® clips are Kite marked to BS5315 (1991) and the company is licensed to ISO 9001. Made from mild steel, zinc protected and used for fixing flexible rubber hoses, metal tubes etc.Size 6XAdjustment . 120 - 150mmAdjustment. 4.3/4 - 5.7/8in

Faithfull Hose Clips are ideal for fixing flexible rubber hoses, plastic hoses and flexible pipes and can be used around the home, in the garden, workshop or the garage, in most applications where a water or air tight seal is required. The non-perforated worm drive used on these hose clips provides a high thread strength with a smooth running, snag-free winding surface. A hex shaped drive nut allows the use of either a slotted screwdriver, spanner, nutdriver or hose clip driver* when tightening or loosening the clips. The Stainless range of hose clips are manufactured using a marine grade 316 W5 stainless steel and are ideal where a high resistance to corrosion is required. Clips are available in a variety of sizes. * The Faithfull Flexi-drive hose clip driver (product code: FAISDHOSE) is perfect for fitting and removing hose clips. The driver features a full sized, soft-grip, non-slip handle and a flexible drive shaft that allows easy access when removing or fitting hose clips in difficult to reach or offset positions. Screw head size: 7mm.The Faithfull FAIHC2XSSB Stainless Steel Hose Clip comes in the following:Size: 2X.Adjustment: 45 - 60mm.

Listing Date:12/18/2020

The Blue Spot Fine Thread G Clamps have a fine thread with reinforced shoulders for strength. They have a malleable cast iron frame, a tommy bar handle and swivel shoe.Size: 102mm (4 inch).

These Forgefix Pozidriv Self-Tapping Screws have countersunk heads and are Zinc Plated for increased resistance to corrosion. They tap their own thread in to a pre-drilled pilot hole in sheet or solid material. They are single threaded to resist pull-out. APPLICATION:Ideal for use in many DIY, ironmongery, engineering, electrical and plumbing applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. Countersunk heads are designed to sink flush with substrates to leave a smooth surface finish.Self Tapping Screw Pozi Countersunk ZP 3/4 x 6 Box 200

The DEWALT DCK654P3T XR Compact TSTAK­ Kit, contains the following: 1 x 18 Volt DCD796 XR Brushless Hammer Drill Driver has an ultra compact, lightweight design. The two speed all metal transmission provides increased runtime and longer tool life. It offers a 15 position adjustable torque control for consistent screwdriving. Chuck: 13mm Keyless.No Load Speed: 0-550/0-2,000/min.Impact Rate: 0-9,350/34,000/bpm.Max Torque: 27/70Nm, 15 Settings.Capacity: Steel: 13mm, Masonry: 13mm, Wood: 40mm.Weight: 1.3kg. 1 x 18 Volt DCF887 XR Brushless Impact Driver is equipped with application control. This is achieved through 3 motor speeds and torque settings. Precision Drive mode offers additional control in screwdriving applications to avoid material and fastener damage. It has a super lightweight and compact design. Bit Holder: 6.35mm (1/4in).No Load Speed: 0-850/0-2,100/0-3,000/min.Impact Rate: 0-1,800/0-2,900/0-3,700/bpm.Max Torque: 26/80/203Nm.Weight: 1.56kg. 1 x 18 Volt DCS355 XR Cordless Oscillating Multi-Tool delivers up to 57 percent more run time over brushed motors. It uses the quick-change accessory system that allows blades and attachments to be changed quickly without the use of tools. No Load Speed: 0-20,000/min. Length: 310mm.Weight: 1.06kg. 1 x 18 Volt 125mm DCG412 XR Angle Grinder has a powerful fan cooled motor and intelligent variable speed trigger and lock-off switch for enhanced work safety and control. It features the XR Lithium Ion Technology and is part of the intelligent XR Lithium Ion Series designed for efficiency and making applications faster. No Load Speed: 7,000/min.Disc Diameter: 125mm, M14 Spindle.Weight: 3.0kg. 1 x 18 Volt 165mm DCS391 Circular Saw with an intelligent trigger allowing total control over all applications. It has a powerful and highly efficient PM58 fan cooled motor with replaceable brushes, which delivers up to 3,700 rotations per minute for a fast cutting action. It has a spindle lock for quick and easy blade change. No Load Speed: 3,700/min.Max Cutting Depth: 90 degree : 55mm, 45 degree : 42.1mm.Blade: 165 x 20mm Bore.Weight: 3.8kg. 1 x 18 Volt DCH273 Brushless XR 3 Mode Hammer is fitted with an electronic clutch for consistently high torque and improved durability. Ideal for drilling anchors and fixing holes into concrete. Modes: Rotary, SDS Hammer, Chisel Only.No Load Speed: 0-1,100/min.Impact Rate: 0-4,600/bpm.Impact Energy: 2.1 Joules.Capacity: Wood: 26mm, Metal: 13mm, Masonry: 24mmWeight: 3.1kg.