Bering Wave, textile jacket

Features
waterproof, windproof and breatheable ergonomically adjusted cut additional padding at palm elastic inserts on wrist, back and fingers for more comfort silicone prints on the inside and fingers for better grip Visor wiper hard shell over the knuckles material doubling on inside and small finger velcro fastener on wrist and gauntlet reflective piping soft, durable Tactel fabric in combination with cowhide Porelle climate membran

To have a maximum safety the helmet must fit tightly and be correctly and securely fastened, in order not to be able to be taken off neither by pulling it nor by rotating it around the head. If it is too big, it may slide down over the eyes or turn in a lateral direction due to movement during riding, blocking the right visibility. Safety Shell in three sizes (M, L and XL) hand made. The new material is a mix of carbon and aramidic fabric.
Internal Polystyrene in three sizes (M, L and XL). The special shape and construction in different density increases mechanical resistance in the event of accidental shock.
Shield thermoformed froma flat sheet. Each shield is a one-of-a-kind piece with unequalled optical features and mechanical resistance. Thanks to this process, the face shield is anti scratch and anti fog and there is no need to use additional lenses on the visor.
The D-Ring Retention System has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding. ECE 22-05 Comfort Cheekpads completely removable and washable, in different thicknesses for a complete customization of the product. Internal Shell completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in teh internal part of teh helmet and to let off the hot air through the back part.
Inner (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA.
Removeable Nose Protector Ventilation
The Shell is a polystyrene with channels for inside air flows. In the front part there is a Air Ventilation with on/off system, which gets the internal helmet ventilation. On the chin part there is an adjustable Air Ventilation.
Aerodynamics Spoiler and Back Air Ventilation: produced in polycarbonate , it has been studied and tested in wind tunnel, so that the point of detachment of the aerodynamic flow is shifted as far away as possible from the shell. This results in less turbulence and therefore fewer vibrations on the helmet itself. This helmet comes standard with a clear visor.

Description:Durable nylon kayak deck hinge mount with split ring, quick release pin and lanyardStrong corrosion resistance and durable in saltwater circumstanceWith 2 stainless steel mounting screws, easy to installWorks great with Kayak Slide Rail Anchor,Also used for marine boat bimini top canopy fittingGreat accessories for kayak, canoe, marine boat, fishing dinghy, raft and so onSpecifciation:Brand: BEST MATELTape: Tape 5Material: 316 stainless steelPackage Included:1 X Deck Hinge

Black Long Sleeve Pockets High Low Bomber Jacket

Outershell
Mix of kangaroo leather and cowhide,approx. 40% kangaroo
Lining
breathable, 3-dimensional foam material (100% polyester) Comfortable, 100% polyester breathable net inner lining
Comfort/Feature
2 inside pocket schoeller®-KEVLAR stretch panels at arm, crutch and back of the knee for maximum comfort stretch leather panels at knees, back and shoulders Perforated leather areas Knee sliders Back hump wristband made from schoeller®-KEPROTEC stretch material
Safety
titanium protectorsat shoulder, elbow and knee SOFT height-adjustable protectors at knee SOFT-protectors at shoulders and elbows and knee detachable TEMPERFOAM padding at hips Leather reinforcement at seat patch schoeller®-KEPROTEC stretch panels below arms, inside arms, crutch and calves upgradable hip protectors Sas-Tec backprotector Safety seams

Material
Polyester Ripstop / washable cow leather / polyester 3D mesh
Lining
Polyester mesh Detachable waterproof Raintex+ membrane Detachable thermo liner
Safety
Shoulder Safetech level 2 (+ Velcro) Elbow Safetech level 2 Back EVA plate 12 mm Pocket back protector prepared 8V long + short connection zipper Laminated reflection: chest / back / sleeves
Comfort
Hotvest prepared Airpanels chest / back / airvents sleeves Detachable hood Zipgrip Straps hip / cuff / lower arm Keyring Easy Cuff light