Bering Ziggy, textile jacket

500 D polyester fabric detachable Reissa®-Membrane: 100% waterproof, 100% windproof, breathable detachable thermo lining shoulder and elbow YF protectors, certified acoording to EN 1621-1 detachable crash foam at back upgradeable with SaS-Tac® SCL-19 back protector, certified according to EN 1621-2:2014 3M Scotchlite™ reflectors AirVent ventilation zips 3 outer pockets 2 waterproof inner pockets connection zip saftey seams

MR. JUMP, the fiber helmet studied in details for comfort, technology and for sure safety for end user. It has been studied and tested to optimize the outside and inside air flows.
OUTER SHELL in tricarboco material, mix of Kevlar, carbon and fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell sizes: XS-L and XL-2XL
INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M and L). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation.
The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding.
MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471
CHEEK PADS completely removable and washable, with different thickness to get a perfect customization od the helmet.
INTERNAL SHELL completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet and to let off the hot air through the back part.
INNER (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper and back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation.
The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses.
weigth: ca. 1000gr

null▶Features:1.Self adhesive2.Will not harm your paint or natural finish3.Can be applied and reapplied for desired look4.Water proof and stain resistant5.Very flexible and stretchable6.UV protected7.Super easy to use8.Low cost compared to a paint job!▶Specification:Model682034Product NameCar Vinyl Wrap StickerColorGreen/ Blue/ Yellow/ Sliver/ Red/ Grey/White/ BlackMaterialVinylThemeAftermarket Parts, Racing, SportsWrapping Tool KitLimited One Wrapping Tool Kit Per eBay AccountFinishMatte Flat ColorPlacement on VehicleLeft, Right, Front, RearSize40x 200cmProduct TypeApplication Tool, Blank Decal Vinyl Sheet(s), Body Decal, Bumper Sticker, Fuel Tank Decal, Hood Decal, Racing Stripes, Tailgate DecalInstallation TemperatureVinyl Might tear if apply below 70°F▶Fitments (For the reference):Application: Universal Fit Car SUV Truck Van Interior Exterior▶Note:1.We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need.2.Please allow 0.5-1 inch difference due to manual measurement.(1inch=2.54cm)3.There are no instructions included in this kit.Professional Installation Is Highly Recommended!4.The color of the actual items may slightly different from the listing images due to different computer screen, thanks for your understanding.▶Package Include:1x Car Vinyl Wrap Sticker

Outer garment
Fibretech 500D, soft & stong fabric Softshell panels Armex : high resistance to abrasion on forearm
Membrane
Waterproof & breathable membrane
Isolation
120 g. removable thermo-alu lining
Protection
Adjustable approved elbow protectors Approved shoulder protectors Pocket for approved back protector
Comfort
Regular fit Fixed mesh lining Anti-flutter system on sleeves Cuff fastening Jacket bottom tightening by elastic cord and stopper High comfort collar Reflective material Zip for connecting with trousers 2 outer pockets 1 back pocket 3 inner pockets Puls Air ventilation system Fitex system waist fastening

Description:100% brand new.Easy to install.Better than the original wiper.More strong and more fit for your car rear windscreen.Dont hesitate to buy it.Part Number: SSB 000150 / SSB000150Rear windscreen wiper armblade for Citroen Xsara Picasso X Y 03 53 51 02 52.Specification:Material:High quality plasticColor:Black brand newSize:Wiper arm: 42.5 x 3.8 x 2.8cmBlade: 41.8 x 3.7 x 1.6cmAperture: 8~9.5mmWeight(Kg):0.25Color:BlackFitment:2001--2005 MG MG ZT Saloon1999--2005 Rover 75 RJ Saloon /EstatePackage Included:1 x Rear Wiper ArmBlade Set

Split the grid in the Wireform jacket. The chassis on this three-season jacket comes with slightly pre-curved arms, ideal for the sportbike riding position. Comfort molded neoprene collar, unique reinforced grid chassis, and a full D3O® (shoulders, elbows, and back) package speak to the Wireform’s riding pedigree. Reflective hits provide visibility in low-light conditions, while a removable insulated SatinCore™ liner extends your riding season deep into the fall.
Features
ICON® Sport Fit Material: DynaxTM Ballistic Nylon Chassis Waterproofing: LEVEL : 1 Protectors: D3O® Impact Protectors - Shoulders, Elbows, Back Liner: Insulated SatinCore™ Liner - Removable 3M® Reflective Accents Reflective Thermoplastic Chest Logo Integrated Flex Zones Neoprene Collar Accordian Flex Zones Pre-Curved Arms YKK® Zippers Interior Zipper Slash & Cargo Pockets Streamlined Sportcuff™ Thumb Loops