Freedom of movement through simplicity and style, the redesigned Airline glove sports slip-on comfort, increased durability, better breathe-ability, and a single layer perforated palm.
Description: 1. A pair of universal replacement 12V shell horns. With universal mounting brackets, installation is simple. No additional work is required. Can be used as direct replacement to the snail shell design or round horns.2. Some cars may have a plug fitted to the horn which you need to replace with 2 spade terminals, but in most cases these horns will fit on to your car with nothing else required.Specification:12V Dual Tone Snail Air Horn (1 Pair)110DB Rating: LOW 410HZ HIGH 510HZDimension of single horn (approximate): Diameter:8.5 cm Depth: 7.5 cmFitting instructions includedEasy to installTo be used only for 2 terminals versionSuitable for cars, van, bikes and boats with 12V power supply Package Included: 2 X 12V Air Horn
To have a maximum safety the helmet must fit tightly and be correctly and securely fastened, in order not to be able to be taken off neither by pulling it nor by rotating it around the head. If it is too big, it may slide down over the eyes or turn in a lateral direction due to movement during riding, blocking the right visibility. Safety Shell in three sizes (M, L and XL) hand made. The new material is a mix of carbon and aramidic fabric. Internal Polystyrene in three sizes (M, L and XL). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Shield thermoformed froma flat sheet. Each shield is a one-of-a-kind piece with unequalled optical features and mechanical resistance. Thanks to this process, the face shield is anti scratch and anti fog and there is no need to use additional lenses on the visor. The D-Ring Retention System has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding. ECE 22-05 Comfort Cheekpads completely removable and washable, in different thicknesses for a complete customization of the product. Internal Shell completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in teh internal part of teh helmet and to let off the hot air through the back part. Inner (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER: Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. Removeable Nose Protector Ventilation The Shell is a polystyrene with channels for inside air flows. In the front part there is a Air Ventilation with on/off system, which gets the internal helmet ventilation. On the chin part there is an adjustable Air Ventilation. Aerodynamics Spoiler and Back Air Ventilation: produced in polycarbonate , it has been studied and tested in wind tunnel, so that the point of detachment of the aerodynamic flow is shifted as far away as possible from the shell. This results in less turbulence and therefore fewer vibrations on the helmet itself. This helmet comes standard with a clear visor.
Thanks to breakthroughs in the study of aerodynamic phenomena, SKWAL boasts a design and silhouette resulting from computational fluid simulations, in the aim of optimizing both stability and soundproofing at high speed. The one-of-a-kind SKWAL lines are reinforced and transformed by 3 embedded LEDs powered by a rechargeable battery (USB charging cable included). SKWAL is one of the world s first major integrated manufacturers to be equipped with this technology. Features 1,470 g Constructed from injected thermoplastic resin Pinlock MaxVision visor a standard feature Visor can be fitted with a Pinlock Max Vision® film insert Quick release visor system "Autoseal" system: flattens the visor onto the helmet, offers better soundproofing and seals the helmet (against water and cold) Integrated UV380 label & anti-scratch sun visor Optimal comfort for the persons wearing glasses Micro lock buckle system Planned location for SHARKTOOTH® Interior bamboo treatment for triple effectiveness: antibacterial, anti-sweating and hypoallergenic
Spidi Super Hydro is the new reference for those looking for maximum protection from water, a high level of therm and a sober design. The special "ROBUST" fit ensures a good fit to different body types. Technical features: 6.6 double layer Nylon outer fabric, with Teflon treatment Waterproof and breathable H2Out membrane laminated to the outer fabric Tenax Flex inserts to facilitate the guidance Forcetech protectors on shoulders and elbows Possibility to insert Warrior back protector certified EN1621-2 Level 1 and Level 2 Ability to insert certified chest protectors Chest and Thorax Warrior Warrior Thermal padding in hollow fiber wadding 200 gr/sq Perimeter zipper for attachment to trousers 4 outside pockets including two waterproof EST Micrometric closure system on the neck Velcro fastening on the sides and sleeves Drawstring narrowing on the bottom "ROBUST" fit Product weight: kg. 2,15Two jackets in one product - Inner jacket usable as a stand alone Integrated adjustment system
Features Waterproof and breathable with fixed membrane Extra supple leather, with a slight distressed effect Thermal lining also wearable independently as a casual vest Classic collar with press-stud Fixed cotton lining 4 external pockets. 5 internal pockets. 1 waterproof wallet pocket Zipped cuffs with press-stud Bottom adjustable with press-studs Connection with trousers thanks to buckle on back approved elbow and shoulder protectors according to the standard 1621-1 + Back pocket to welcome a certified back protector PPE certified
