Milwaukee M12CID-0 12v FUEL Impact Driver - Bare Unit

The Einhell Power-X-Change Combi & Impact Driver Twin Pack, contains the following: 1 x 18 Volt TE-CD 18-2 Li-i Power X-Change Combi Drill is a powerful and versatile tool for screwdriving, drilling and hammer drilling jobs. It has a robust, long-lasting 2-speed metal gear box for high torque and torque slip coupling that prevents over tightening of screws. Chuck: 13mm Keyless. No Load Speed: 0-320/0-1350/min. Max Torque: 48Nm 25 Settings. Capacity: Concrete: 15mm. Weight: 1.76kg. 1 x 18 Volt TE-CI 18 LI Power X-Change Impact Driver is fitted with a unique triathlon motor that is powerful and efficient for the highest demands in power-sapping screwdriving jobs. The special impact mechanism eliminates any torsion force on the user’s wrist. Short, lightweight design with ergonomic soft-grip surfaces and a rugged aluminium housing with additional rubber supports for increased protection. Bit Holder: 6.35mm (1/4in). No Load Speed: 0-2,300/min. Impact Rate: 0-3,200/bpm. Max Torque: 140Nm. 1 x 18 Volt Power-X-Change Charger that features a 6-step charging condition display and is ready for wall-fastening. The charger uses an intelligent charging-management-system for long battery life (battery status will be constantly checked and accordant loaded, a deeply discharged battery will be charged in repair mode). Input Power: 240 Volt. Output Voltage:21 Volt. Charging Time: 1.5Ah: 30 min, 3.0Ah: 60 min, 5.2Ah: 130 min. Weight: 0.5kg. Also comes with 2 x 18 Volt 1.5Ah Power X-Change Li-Ion Batteries and 1 x Toolbag.

Multi-purpose combination square for use in both wood and metalworking applications. Each square features a high quality cast and machined sliding stock, fitted with a stainless steel rule engraved with both imperial and metric graduations, a spirit level and marking scribe.The Faithfull combination square has at least 10 different uses including:-Measuring rule with metric and imperial scale, 90° inside square, 90° outside square, 135° inside square, 45° inside square, horizontal level, vertical level, T-square slide, marking gauge and depth gauge.Ruler Length : 400 mm / 16 inch.

Paslode IM350+ Diamond point clipped head Nail packs with paper strip, supplied with Paslode Special Impulse gas fuel cells.FINISH: All Paslode nails are Chrome 6, cadmium and lead free and are available in five finishes to meet corrosion requirements.Bright: Economy and bright nails meet the Eurocode 5 requirements for applications in service class 1 (indoor) Specification - No coating.Galv Plus : Meet the Eurocode 5 requirements for applications in service class 1 and 2 (indoor and covered outdoor) Specification - Zn / Al alloy approx 15µm.Electro Galv : Meet the Eurocode 5 requirements for all applications in service class 1 and 2 (indoor and covered outdoor) Specification - Zn and chromate minimum 7µm.Hot Dipped Galv : Meet the Eurocode 5 requirements for all applications in service class 1, 2 and 3 (indoor, covered outdoor and outdoor) Specification - Zinc coating minimum 50µm Stainless Steel : Meet the Eurocode 5 requirements for all applications in service class 1, 2 and 3 (indoor, covered outdoor and outdoor) Specification - A2 according to AISI 304, and A4 according to AISI 316.SHANK: Smooth Shank: The standard nail, offering high shear value and lowest withdrawal resistance. Fixing across the grain. Fixing into end grain. Clenching applications. Specification - Number of centres will vary with shank diameter.Unilock Shank : Increases withdrawal resistance. Drives easier than ring shank fixing across the grain. Specification - The ringed parts have 24 rings per inch.Ring Shank : Provides the highest withdrawal resistance. Fixing across the grain. Specification - RPI (Rings Per Inch) vary from 16 to 32 depending on Specification.HEAD TYPES :Round Head : The head area is designed to maximise resistance to the head being pulled through Specification - Head size between 2.0 and 2.5 times wire diameter according to EC5Clipped Head : Increases number of nails per strip. The head area is designed to maximise resistance to the head being pulled through Specification - Head area corresponding to full round head area, according to EC5

DEWALT Mesh Sanding Discs last at least 4 times longer than traditional DEWALT sandpaper discs. Fibres are drawn away from the surface of the sanding disc into the small holes, and don't sit between the material and abrasive. This optimises the sanding effect. These sanding discs enable dust to be drawn through the mesh across a wider area rather than being limited to distinct holes in traditional sanding discs. They are also much easier to select as there is no requirement to match a specific dust extraction hole pattern. The mesh sanding discs have hook and loop fastening for quick and easy attachment. They can be easily cleaned to help prolong their life.The DTM3125 Mesh Sanding Discs have the following specifications:Size: 150mm.Grit: 120.Pack quantity: 5.

128mm 5 "HSS Centro de acero de alta velocidad automático del sacador por resorte Pulse marcador Dent Con Impact ajustable y de acero endurecido Cuerpo

The Milwaukee Torque Lock™ Locking C-Clamp with Swivel Pads, provide surface stabilisation and protects work surface from damage. The patent pending thumb screw provides the user with a more convenient geometry for hand force, while providing clearance to generate more torque with the unique screwdriver through-hole design. The hardened jaws give more gripping power, and are made from forged alloy steel for maximum durability and offers outstanding protection against rust, increasing the tool life by reducing corrosion. Milwaukee locking tools are made for the toughest jobsite. Milwaukee stands behind their product and offers a Limited Lifetime Warranty with all locking tools. Capacity: 102mm (4in).Clamping Strength: 226.7kg (500lbs).