Cross section allows use on convex and concave surfaces. Tapered very slightly towards point both in width and thickness. Smooth Cut: Approx 62 teeth per 25mm (Fine).Second Cut: Approx 36 teeth per 25mm (Medium).Bastard Cut: Approx 26 teeth per 25mm (Coarse).Size. 300mm (12in)Cut half round bastard Flat Side: Double CutHalf Round: Double Cut.Tanged
Yale brass padlocks are a good quality multi-purpose solution. They are essential padlocks available in a range of sizes and are suitable for a multitude of security applications. The YE1 padlocks are general purpose padlocks with a solid brass body and chrome plated shackle. They are great for securing items which require a standard level of security. Supplied with 3 keys.Specifications: Body dimensions: 50 x 38 x 16mm.Padlock total height: 72mm.Shackle internal: 26 x 26mm.Shackle thickness: 8mm.
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S
The Bosch BT150 Tripod is absolutely secure stance on any floor. Suitable for GPL 5 c; GCL 25; GPL 3 ; GLL 2-15; GLL 3-80 P; GLL 2-80 P; GLL 2-50; GLL 3-50; GLM 50; GLM 80; GLM 150; GLM 250 VF; GIM 60 L Professional Features: Robust aluminium design For work heights from 55 to 157 cm Functionality and precision due to circular vial 1/4" tripod thread Optimised working with line and point laser Good transportability due to low weight
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/4in ShankCutting Diameter: 12.7 mm 1/2in. Cutting Length: 19 mm. Shank Diameter: 1/4in.
Self guiding cutters with bearings mounted for trimming and bevelling timber, lippings and plastic laminate edges for cabinet making, countertop production or any shaping applications. Bearing guided cutters are suitable for both straight and curved work, bearings are normally fractionally larger than cutter diameter, to avoid surface scoring. Uses:Trimming plastic or plywood overlay.Copy profiling - use the bearing to follow a template or base edge of board. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. Tooling Tungsten Carbide1/2in Shank.Tooling Tungsten Carbide1/2 in Shank.Angle A = 90° D = 12.7 mmC = 25 mm
