Held Nela, textile pant women

Features
with steel cap screwed and glued sole
material
outside: 100% suede leather inside: 100% suede leather sole: rubber

Outer shell
water- & wind-repellent, breathable, elastic Softshell fabric (96% nylon, 4% elasthane)
Lining
mesh lining (100% polyester)
Fit/features
3 external pockets 2 inner pockets
Protection
EN 1621-1 CE-certified soft protectors at shoulders & elbows optional EN 1621-2 back protector sporty look (PU) soft foam cups on shoulders reflective piping Connecting zip

Description:1. The car antenna is easy to install and its a great decoration to make your car look more cool and differ from the common.2. The advanced car antenna is in position to eliminate intrinsic static electricity.3. It harmonizes with the car body and dress up your car, provides good condition for receiving signals.Fitments:Fit for these cars:2003 - 2008 BMW Z41996 - 2002 BMW Z31998 - 2006 BMW M3 Convertible2001 - 2006 BMW 330ci2001 - 2006 BMW 325ci1995 - 1999 BMW 323ic1993 - 1999 BMW 318ic1995 - 1999 BMW 318ti2004 - 2006 Chevrolet Aveo2002 - 2009 Dodge Sprinter2001 - 2005 Lexus IS3002002 - 2009 Mitsubishi Lancer2002 - 2006 Mini Cooper2004 - 2009 Mazda 32005 - 2010 Mazda 52003 - 2008 Mazda 62002 - 2003 Mazda Protege52006 - 2010 Mazda MX-5 Miata2003 - 2009 Nissan 350z2003 - 2009 Pontiac Vibe2005 - 2010 Scion tC2007 - 2010 Toyota Yaris Hatchback2004 - 2009 Toyota Prius2003 - 2008 Toyota Matrix2003 - 2008 Toyota Corolla2004 - 2008 Toyota Solara Convertible1998 - 2004 VW Jetta / Bora / Golf / Polo Mk41996 - 2000 VW Passat B5Dimension :Approx. Length: 16 / Base Width: 0.5/ Thread Diameter: 5mm/ Thread Length: 6mm(NOT INCLUDE THE BASE)Perfect OEM Replacement Parts, Best Quality and Satisfaction GuaranteedPlug and Play, Few Minutes Easy Installation without ToolsPackage Included:1 x Antenna1 x Antenna BasePicture details:

Netzkabel für die BMW Zusatzsteckdose. Das Kabel hat eine Länge von 120 cm. - Klan-e BMW Anschlusskabel

MR. JUMP, the fiber helmet studied in details for comfort, technology and for sure safety for end user. It has been studied and tested to optimize the outside and inside air flows.
OUTER SHELL in tricarboco material, mix of Kevlar, carbon and fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell sizes: XS-L and XL-2XL
INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M and L). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation.
The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding.
MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471
CHEEK PADS completely removable and washable, with different thickness to get a perfect customization od the helmet.
INTERNAL SHELL completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet and to let off the hot air through the back part.
INNER (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper and back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation.
The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses.
weigth: ca. 1000gr

Features
Former JUMP Glove Silicone printing on palms and finger tips for improved grip and braking control Long lasting and flexible material for the perfect fit Lightweight design with bold, non-fade graphics Seamless rollover fingertips Synthetic leather palm, with double layer thumb reinforcement Adjustable Velcro? wrist closure for secure and adjustable fit Pre-curved tailoring for the best fit possible, and helps to eliminate arm pump